Your cart

Total
CAD
Shipping and discount codes are added at checkout.

Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com          Ordering/Questions

Spinnaker Car Parts -
Bayonet Pins & Bell Fittings


While Ring Cars and Toggle Cars, used with standard Piston pole ends, are suitable for smaller boats, larger boats (and more demanding applications) often benefit from the use of Poles with Bell Ends or Bayonet Pin Receiver Ends.

Listed below are common Replacement Parts for Bayonet Pin & Bell Fittings.
Complete Spinnaker Cars with Bayonet Pin or Bell Fittings are listed by Track size and type, See Spinnaker Cars.

Other Spinnaker Car Parts will be listed under your specific Spinnaker Car, See Spinnaker Cars.

See also, Spinnaker Poles & Parts.
 


Spinnaker Car Parts - Bayonet Pins & Bell Fittings

Replacement Bayonet Pins & Toggles

Replacement Metric Bell Fittings
 

Replacement Bayonet Pins & Toggles
Replacement Bayonet Pins and Toggles from a variety of manufacturers are available separately. They are also available as part of a complete Spinnaker Car, See Spinnaker Cars.
 
Forespar TS Pin & Toggle Ass'y for Spinnaker Car: For TS-PT:
Replacement Forespar TS Pin & Toggle Assembly fits all Forespar TS type Spinnaker Pole ends, and Spinnaker Cars with a 1/2" vertical Pin and clearance for a 1" Toggle. Stainless Steel TS Pin is 1" OD x 3 5/8" long, SS Toggle is 1" high with hole for a 1/2" Pin, and is 2 3/4" between Pin centers.

 

For_TS-PT.gif (5795 bytes)

 

Forespar TS Pin only: For TS-P:
Replacement Forespar TS Pin only, fits all Forespar TS type Spinnaker Pole ends, and Toggles with 1/2" Pins and 1/2" ID clearance. Stainless Steel TS Pin is 1" OD x 3 5/8" long, with hole for 1/2" Pin.

 

Forespar TS Toggle only: For TS-T2:
Replacement Forespar Toggle only, fits Forespar TS Pin, and Spinnaker Cars with a 1/2" Pin and clearance for a 1" Toggle. Stainless Steel Toggle is 1" high with hole for a 1/2" Pin, and is 2 3/4" between Pin centers.

 


Nicro-Fico 1/2" Bayonet Pin only: NF 73-P1:
Replacement Nicro-Fico 1/2" Bayonet Pin only, fits all Nicro-Fico 1/2" Bayonet type Spinnaker Pole ends. Stainless Steel Bayonet Pin is 1/2" OD x 3 1/8" long (beneath head), head is 3/8" thick with hole for 3/8" pin. Unit is (maximum) 4 3/8" long.

 

Nicro-Fico Bayonet Pin Toggle only: NF 73-T1:
Replacement Nicro-Fico Bayonet Pin Toggle fits all Nicro-Fico 1/2" and 5/8" Bayonet Pins and appropriate Spinnaker Cars. Chrome Bronze Toggle is 1 1/16" high x 1 1/16" wide x 1 7/8" long with (2) holes for 3/8" pins.

 

Replacement Nicro-Fico 5/8" Bayonet Pin only: NF 73-P2:
Replacement Nicro-Fico 5/8" Bayonet Pin only, fits all Nicro-Fico 5/8" Bayonet type Spinnaker Pole ends. Stainless Steel Nicro-Fico 5/8" Bayonet Pin is 5/8" OD x 3 1/8" long (beneath head), head is 7/16" thick with hole for 3/8" pin. Unit is (maximum) 4 5/8" long.

 


Sparcraft Pin & Toggle Ass'y for Spinnaker Car w/ 1/2" Pin: SPC 73-13PT-2:
Replacement Sparcraft Bayonet Pin & Toggle (Type 2) Assembly fits all Sparcraft Bayonet type Spinnaker Pole ends, and Spinnaker Cars with a 1/2" vertical Pin and clearance for a 1" Toggle. Assembly includes Sparcraft Bayonet Pin, SPC 73-13P, and SS Toggle SPC 73-12T2.

 

Sparcraft Bayonet Pin only: SPC 73-13P:
Replacement Sparcraft Bayonet Pin only, fits all Sparcraft Bayonet type Spinnaker Pole ends. Stainless Steel Sparcraft Bayonet Pin is 7/8" OD x 4" long (beneath head), head is 9/16" thick with hole for 1/2" pin. Unit is (maximum) 5 3/4" long.

 

SC_73-13Ph.gif (4246 bytes)

 

Sparcraft Type 2 Toggle only: SPC 73-12T2:
Replacement Sparcraft Toggle (Type 2) fits Sparcraft Bayonet Pin and Spinnaker Cars with a 1/2" vertical Pin and clearance for a 1" Toggle. Stainless Steel Toggle is 1" high x 1 1/4" wide with holes for 1/2" Pins, and measures 1 5/8" between Pin centers. Horizontal (1/2") Pin is included.

 

 

Sparcraft Pin & Toggle Ass'y for Spinnaker Car w/ 5/8" Pin: SPC 73-13PT-1:
Replacement Sparcraft Bayonet Pin & Toggle (Type 1) Assembly fits all Sparcraft Bayonet type Spinnaker Pole ends, and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Assembly includes Sparcraft Bayonet Pin, SPC 73-13P, and SS Toggle SPC 73-12T1.

 

Sparcraft Bayonet Pin only: SPC 73-13P:
Replacement Sparcraft Bayonet Pin only, fits all Sparcraft Bayonet type Spinnaker Pole ends. Stainless Steel Sparcraft Bayonet Pin is 7/8" OD x 4" long (beneath head), head is 9/16" thick with hole for 1/2" pin. Unit is (maximum) 5 3/4" long.

 

SC_73-13Ph.gif (4246 bytes)

 

Sparcraft Type 1 Toggle only: SPC 73-12T1:
Replacement Sparcraft Toggle (Type 1) fits Sparcraft Bayonet Pin and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Stainless Steel Toggle is 1 3/16" high x 1 3/8" wide with holes for 5/8" (Vertical) and 1/2" (Horizontal) Pins, and measures 1 5/8" between Pin centers. Horizontal (1/2") Pin is included.

 

SC_73-13T1.gif (9506 bytes)

Z-Spar Spinnaker Pin & Toggle Ass'y: Z-73-ZPT:
Replacement Z-Spar Bayonet Pin & Toggle Assembly fits all Z-Spar Pin type Spinnaker Pole ends, and Spinnaker Cars with a 12mm vertical Pin and clearance for a 1 5/16" (34mm) Toggle. Z-Spar Pin is (maximum) 25mm OD x 100mm (4") long (tip to Pin center), working section is 16mm OD, with a minimum 10mm OD. Aluminum Toggle is 1 5/16" (34mm) high with hole for a 12mm Pin.

 


Replacement Metric Bell Fittings
Metric Bell Fittings are available separately. Suitable for use with a variety of Spinnaker Cars having 10mm or 12mm vertical Pins, they are also available as part of a complete Spinnaker Car, See Spinnaker Cars. Metric Bell Pole End fittings, that the Bells work with, are commonly found on Poles of 50, 60, 70, 80, and 100mm OD, See: Metric Spinnaker Poles & fittings.

 

Standard Metric Small Bell w/ Toggle for 12mm Pin: Har B-130:
Metric Small Bell & Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Small Bell Pole Ends. Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm vertical Pin and is 1 3/8" (34mm) high. Metric Small Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end.

 

Toggle only for Har B-130: Har B-130T:
Replacement Toggle only for Har B-130 Metric Small Bell and Toggle Assembly. Cast Aluminum Toggle fits on outside of Bell casting and is 1 3/8" (34mm) high x 2 1/8" (54mm) wide with 12mm hole for attachment to Spinnaker Car.

 

Trigger only for Har B-130: Har B-130TR:
Replacement Trigger only for Har B-130 Metric Small Bell and Toggle Assembies. Cast Aluminum Trigger has 12mm hole for attachment to Small Bell fitting. Limited Availability.

 

Special Metric Small Bell w/ Toggle for 10mm Pin: Har B-130-10:
Metric Small Bell & Toggle Assembly is as Har B-130, above, but Toggle has Stainless insert bushings for use with Spinnaker Cars having a 10mm vertical Pin. Specially modified for use with Isomat NGA-51-BS, and other Spinnaker Cars with a 10mm Vertical Pin.

 

Toggle only for Har B-130: Har B-130T-10:
Replacement Toggle only for Har B-130-10 Metric Small Bell and Toggle Assembly. Cast Aluminum Toggle fits on outside of Bell casting and is 1 3/8" (34mm) high x 2 1/8" (54mm) wide with Stainless insert bushings to provide a 10mm hole for attachment to Spinnaker Car.

 

 

Metric Large Bell w/ Toggle for 12mm Pin: Har B-120:
Metric Large Bell & Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 12mm vertical Pin and is 1 3/8" (34mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end.

 

Toggle only for Har B-120: Har B-120T:
Replacement Toggle only for Har B-120 Metric Large Bell and Toggle Assembly. Cast Aluminum Toggle fits on outside of Bell casting and is 1 3/8" (34mm) high x 2 1/2" (64mm) wide with 12mm hole for attachment to Spinnaker Car. Limited Availability.

 

 
Special Metric Large Bell w/ Toggle for 10mm Pin: Har B-120-10:
Metric Large Bell & Toggle Assembly is as Har B-120, above, but Toggle has Stainless insert bushings for use with Spinnaker Cars having a 10mm vertical Pin. Specially modified for use with Isomat NGA-51-BL, and other Spinnaker Cars with a 10mm Vertical Pin.

 

 

Francespar Large Bell w/ Toggle for 10mm Pin: FSP B-120SC:
Francespar/Sparcraft Large Bell & Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa / Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 10mm vertical Pin and is 1 1/2" (37mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. As used with Isomat NGA-51-BL, and other Spinnaker Cars.

 

Toggle only for FSP B-120SC: FSP B-120SC-T:
Replacement Toggle only for FSP B-120SC Metric Large Bell and Toggle Assembly. Cast Aluminum Toggle fits between Bell casting ears and is 1 1/2" (37mm) high x 1 9/16" (40mm) wide x 68mm long with a 10mm hole for attachment to Spinnaker Car, and hole for cotter pin.

 

Francespar Large Bell w/ Toggle for Ball-Bearing Spinnaker Car: FM 30B-B120B-BTA:
Replacement Francespar/ Sparcraft Large Bell & Toggle Assembly for use with FM 30B-B120B Recirculating Ball Spinnaker Car. Toggle has hole for 8mm vertical Pin and is 1 1/2" (37mm) high, Francespar/ Sparcraft Large Bell fitting is compatible with spinnaker poles using Francespar or Barbarossa/ Harken inboard Large Bell Pole Ends, See: Metric Spinnaker Poles & Parts.

 

 
Toggle only for Ball-Bearing Spinnaker Car: FM 30B-B120B-T:
Replacement Toggle only for FM 30B-B120B Recirculating Ball Spinnaker Car. Special Extruded Aluminum Toggle (with Bushings) is 1 1/2" (37mm) high x 1 9/16" (40mm) wide x 81mm long, with an 8mm hole for attachment to Spinnaker Car, and a 12mm hole for attachment to Francespar/ Sparcraft Large Bell fitting.  

~ Back to Spinnaker Car Main Page ~

~ Back to Spars Main Page ~

~ Home ~