Your cart

Total
CAD
Shipping and discount codes are added at checkout.

Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
 Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com          Ordering/Questions

D-Section Internal Gooseneck Assemblies
Internal Gooseneck Assemblies and Parts
Kenyon Internal Gooseneck Assemblies allow easy control of up to three internal lines. An outhaul on the bottom centerline which is led to a cleat on the underside of the boom, or aft to the cabin top, and a reefing line on each side. Reefing lines go over a sheave and down, and can be cleated at the gooseneck with integral friction-lock lever-action cams, or lines can be led to the deck and cleated aft on the cabin top. SS cover plates protect sheave and/or cam, and keep the reefing lines captive at all times.

Note: Kenyon Old-Style Internal Gooseneck Assemblies featured Spring Cams (with or w/o handles), and different reef sheaves than the improved version. The Old-Style units are easily identified by the absence of the SS cover plates. While upgrading to the improved New-Style cam arrangement using one of the K-11442 Conversion Kits (below) is recommended, original parts for the Old-Style gooseneck are still available. See Parts for Old-Style D-Section Internal Gooseneck Assembly.
D-Section Internal Gooseneck Ass'y w/ Toggle/Tack: K-43022A:
Cast aluminum gooseneck assembly incorporates provisions for internal outhaul and 2 internal reef lines. Outhaul line exits through aluminum sheave, K-198-4A, on centerline and runs along boom bottom to a cleat. Reef lines exit port and starboard running past lever action cams, over delrin sheaves, and down. SS cover plates keep lines on sheaves at all times. Includes SS combination Toggle/Tack/Reef Hook Assembly K-10518A. Toggle attaches to any Kenyon gooseneck bracket designed for 1 1/2" toggle and 1/4" vertical pin. Vertical pin, CP4-61K, is not included. Distance from vertical Toggle Pin to boom tube is 5".

 

K-43022A
Gooseneck Pin for 1 1/2" Toggle & SS Bracket: CP4-61K:
Clevis pin is 1/4" diameter x 1 7/8" long. Used to attach the K-10518 1 1/2" Gooseneck Toggles to a variety of SS Gooseneck Brackets.

 
D-Section Internal Gooseneck Ass'y: K-43022:

As D-43022A, above, but without SS combination Toggle/Tack/Reef Hook Assembly, K-10518A. Attaches to K-10518A or other Toggles up to 11/16" wide, using a 3/8" bolt and locknut (included). Distance from horizontal Pin hole to boom tube is 4".

 

K-43022
D-Section Gooseneck Ass'y w/ Port Cam: K-43022P:

D-Section Gooseneck Ass'y w/ Starboard Cam: K-43022S:

As K-43022, above, but with single reef cam, sheave and cover plate. Specify Port or Starboard Cam.



 

 
D-Section Internal Gooseneck Ass'y w/o Cams: K-43022NC:

As K-43022, above, but with SS spacers, K-11413, in place of the reef cams. For use where reef lines are led down to the deck and cleated aft on the cabin top.

 

D-Section Internal Gooseneck Ass'y for Outhaul: K-11103A:

As K-43022, above, but with outhaul sheave only, and no provisions for reef lines.

 
D-Section Gooseneck Ass'y for Jib Club: K-11103:

As K-11103A, above, but with no sheaves - for staysail booms, jib clubs, and other booms with no internal lines. Commonly used with club pedestals and loose-footed jibs where the tack is secured by means of a pennant attached to the base of the stay. Casting extends 4 1/2" (maximum) forward of the boom tube. Distance from horizontal Pin hole to boom tube is 4".

 
Parts for D-Section Internal Gooseneck Assemblies
Gooseneck Toggle/Tack w/ Reef Hooks: K-10518A:

Used with the K-10554 gooseneck bracket, and Kenyon 2333 or "D" section boom, this combination Toggle/Tack/Reef Hook Assembly features 3 tack positions and includes 3/8" tack fastpin, K-10399. Takes 1/4" vertical pin and 3/8" horizontal pin. Two 1/4" reef hooks allow for ease of reefing from either side of the boom. Toggle portion is 1 1/2" high x 11/16" wide with 1" between pin centers. Unit (excluding Reef Hooks) is 4" high x 11/16" wide x 2 1/4" long.

 

 K-10518A
Gooseneck Pin for 1 1/2" Toggle & SS Bracket: CP4-61K:
Clevis pin is 1/4" diameter x 1 7/8" long. Used to attach the K-10518 1 1/2" Gooseneck Toggles to a variety of SS Gooseneck Brackets.

 
D-Section Internal Gooseneck Casting: K-10463:

Replacement casting only for any of the Kenyon internal gooseneck assemblies listed above. Casting extends 4 1/2" (maximum) forward of the boom tube. Distance from horizontal Pin hole to boom tube is 4".

 
Outhaul Sheave for D-Section Gooseneck: K-198-4A:

Anodized aluminum sheave is 1" OD x 7/16" wide x 1/4" ID.

 
Outhaul Sheave Axle for D-Section Gooseneck: K-10478:

SS axle pin for Outhaul (Lower) Sheave is 1/4" diameter x 13/16" grip, with a turned groove on each end to accept 1/4" SS Snap Rings, K-63016 (2 included).
SS Snap Rings for 1/4"Axle Pin: K-63016-2P:

In 2-pack. Require small snap ring pliers for attachment.

 
Double Reef Cam Conversion Kit for D-Section: K-11442:

Cam Conversion Kit for D-Section Internal Gooseneck converts Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Kit includes everything necessary for 2 reef lines including Cam levers, adjustable friction washers, reef sheaves, SS spacers, Cover plates, bolts and locknuts. Individual components are listed separately, below. The only machining required is to drill the old-style 1/4" sheave axle (forward) hole to 5/16".

 

 K-11443

 
Sheave Only Conversion Kit for D-Section: K-11442NC:

Sheave Conversion Kit for D-Section Internal Gooseneck converts Old-Style Gooseneck to the New-Style with Cover Plates, Sheaves, and No cams. Easily installed Kit includes everything necessary for leading reef lines down and aft, including (2) reef sheaves, (4) SS spacers, Port and Starboard Cover plates, bolts and locknuts. Individual components are listed separately, below. As K-11442, above, but with 2 SS Spacers to replace the reef cams. This Kit converts any D-Section Internal Reefing Gooseneck (Old or New-Style) to the K-43022W Gooseneck Assembly, above. Old-style Goosenecks require drilling the 1/4" sheave axle (forward) hole to 5/16".

 
Port Reef Cam Conversion Kit for D-Section: K-11442P:

Starboard Reef Cam Conversion Kit for D-Section: K-11442S:
Single Cam Conversion Kit for D-Section Internal Gooseneck converts Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Kit includes everything necessary for single reef line including Cam lever, adjustable friction washers, reef sheave, SS spacer, Cover plate, bolts and locknuts. Individual components are listed separately, below. The only machining required is to drill the old-style 1/4" sheave axle (forward) hole to 5/16". Specify Port or Starboard.

 
Reefing Sheave for D-Section Gooseneck: K-11409:

Turned white Delrin Sheave is 7/8" OD x 1/2" (.500") wide x 7/16" ID. With Rope Groove.

 

 K-11412
Reefing Sheave Spacer for D-Section Gooseneck: K-11410:

SS spacer is 7/16" OD x 5/16" ID x .525" long.

 

  
Cam Spacer for D-Section Gooseneck: K-11413:

SS spacer is 1/2" OD x 3/8" ID x .525" long. Used in place of Cams when reef lines are not cleated at the gooseneck.

 

 k-11413.gif (3301 bytes)
SS Cover Plate for D-Section Gooseneck - Port: K-11408P:

SS Cover Plate for D-Section Gooseneck - Star.: K-11408S:

Formed SS cover plate has 5/16" forward hole for sheave bolt, and 3/8" aft hole for cam bolt. Specify Port or Starboard.

 
Gooseneck Reef Cam - Port: K-11246P:

Gooseneck Reef Cam - Starboard: K-11246S:

Cast aluminum Cam lever fits on 3/8" bolt and has recesses for special friction-lock washers, K-10862 (2 included). Specify Port or Starboard.

 

K-11246S
Friction-lock washers for Reef Cams: K-10862:

Special green-colored friction-lock washers made of an impregnated synthetic allow for precise adjustment of cam tension and protect cams from corrosion.

~ Back to D-Section Boom Page ~

~ Back to Kenyon Main Page ~

~ Home ~