 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Kenyon Exit Blocks |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Kenyon Exit Blocks |
|
|
|
|
| Kenyon Exit Blocks | |
Exit Blocks incorporate a sheave, and are used to exit any internal
control line (halyards, pole lifts, etc.) from a spar where a directional
change of 90 to 180 degrees is required. Kenyon Exit Blocks are listed here,
Other Exit Blocks are available.
See: Exit Blocks
or, depending on the kind of spars you have, See also:
Isomat Exit Blocks, or
Z-Spar Exit Blocks.
See Kenyon Exit Plates
for in-line exit applications (Halyard Exits) where there is no directional change.
|
|
|
|
|
| Stainless Steel Exit Block w/ Hood: K-153:
Internal SS Exit Block is used primarily for outhaul wire pennants, thru-deck wire leads, and in other applications. SS sheave (K-198-4SS) is 1" diameter x 1/4" wide and will handle wire or line up to 3/16". Special Assembly with angled hood over sheave fits in cutout 1" long x 3/8" wide and projects 7/8" deep. Unit is 2 9/16" long x 1" wide, and is mounted with (2) 3/16" (#10) FH screws on 1 7/8" centers.
|
|
| Stainless Steel Exit Block for flat surfaces: K-154:
Internal SS Exit Block is used on flat surfaces, primarily for spinnaker pole lifts, spinnaker car controls, outhaul wire pennants in a variety of other applications. SS sheave (K-198-4SS) is 1" diameter x 1/4" wide and will handle wire or line up to 3/16". Assembly fits in cutout 1" long x 3/8" wide and projects 1" deep. Unit is 2 9/16" long x 1" wide, and is mounted with (2) 3/16" (#10) FH screws on 1 7/8" centers.
|
|
|
SS Exit Block for flat surfaces w/ Narrow Sheave: K-154N:
As K-154, above, but with sheave for up to 3/32" wire. Internal SS Exit Block is used on flat surfaces, primarily for spinnaker pole lifts, spinnaker car controls, outhaul wire pennants in a variety of other applications. SS sheave (K-198-4N-SS) is 1" diameter x 1/8" wide and will handle wire or line up to 3/32". Assembly fits in cutout 1" long x 1/4" wide and projects 1 1/4" deep. Unit is 2 9/16" long x 1" wide, and is mounted with (2) 3/16" (#10) FH screws on 1 7/8" centers.
|
|
| Stainless Steel Exit Block for curved surfaces: K-154C:
Internal SS Exit Block is used primarily for spinnaker pole lifts, spinnaker car controls, outhaul wire pennants, and on curved surfaces in other applications. SS sheave (K-198-4SS) is 1" diameter x 1/4" wide and will handle wire or line up to 3/16". Assembly fits in cutout 1" long x 3/8" wide and projects 1" deep. Unit is 2 9/16" long x 1" wide, and is mounted with (2) 3/16" (#10) FH screws on 1 7/8" centers. As K-154, above, but for use on curved surfaces.
|
|
|
|
|
|
SS Exit Block w/ Wide Sheave for flat surfaces: K-152W:
Internal SS Exit Block is used primarily in boom outhaul applications. Aluminum sheave (K-198-3.5A) is 7/8" diameter x 7/16" wide and will handle wire up to 3/16" or line up to 5/16". Assembly fits in cutout 1 3/8" long x 5/8" wide and projects 3/4" deep. Unit is 2 7/8" long x 1" wide, and is mounted with (2) 3/16" (#10) FH screws on 2 7/16" centers. As used in early J/24 and other Boom outhaul applications.
|
|
|
SS Exit Block w/ Wide Sheave for curved surfaces: K-152C-4:
Internal SS Exit Block is used primarily for spinnaker pole lifts, spinnaker car controls, outhaul wire pennants, and on curved surfaces in other applications. Aluminum sheave (K-198-3.5A) is 7/8" diameter x 7/16" wide and will handle wire up to 3/16" or line up to 5/16". Assembly fits in cutout 1 3/8" long x 5/8" wide and projects 3/4" deep. Unit is 2 7/8" long x 1 3/16" wide, and is mounted with (4) 3/16" (#10) RH screws on 2 7/16" x 3/4" centers. 1315
|
|
|
|
|
| Stainless Steel Exit Block: K-11110P: Internal SS Exit Block is used for halyards, spinnaker pole lifts and other control lines. Plastic sheave (K-199-4B) is 1 1/2" diameter x 15/32" wide and will handle line up to 3/8" diameter. Assembly fits in mast cutout 1 3/4" high x 11/16" wide and projects 1 7/8" inside of mast. Mounting flanges are 1 3/4" high x 1 15/16" wide, and are at 90 degrees to the sheave for use on flat surfaces; flanges can also be bent to fit a variety of curved surfaces. Assembly is mounted with (4) #10 (3/16") fasteners on 1 5/16" (vertical) x 1 7/16" (horizontal) hole centers.
|
|
| Stainless Steel Exit Block: K-11110A: Internal SS Exit Block is used for halyards, spinnaker pole lifts and other control lines. Aluminum sheave (K-10545-1) is 1 1/2" diameter x 3/8" wide and will handle 1/8" wire, or rope up to 5/16" diameter. Assembly fits in mast cutout 1 3/4" high x 9/16" wide and projects 1 7/8" inside of mast. Mounting flanges are 1 3/4" high x 1 15/16" wide, and are at 90 degrees to the sheave for use on flat surfaces; flanges can also be bent to fit a variety of curved surfaces. Assembly is mounted with (4) #10 (3/16") fasteners on 1 5/16" (vertical) x 1 7/16" (horizontal) hole centers.
|
|
| Stainless Steel Exit Block: K-11110A-1: As K-11110A, above, but mounting flanges already angled for use on curved surfaces. Flanges can be bent more or less, to fit a variety of curved surfaces. Unit now features removable sheave.
|
|
| Stainless Steel Exit Block: K-11110A-2: As K-11110A-1, above, but mounting flanges angled severely for use as Main Halyard Sheave Box on the 2040 Mast Section.
|
|
|
|
|
| Aluminum Exit Block: K-1555:
Internal Exit Block is used for halyards, spinnaker pole lifts and other control lines. Welded aluminum block assembly is finished with black epoxy coating. Aluminum sheave (K-198-7A) is 1 3/4" diameter x 31/64" wide and will handle 3/16" wire, or rope up to 7/16" diameter. Assembly fits in mast cutout 2 1/4" high x 3/4" wide and projects 2" inside of mast. Mounting flange is 3 1/4" x 1 1/2" plate, slightly curved to fit a variety of mast surfaces. Assembly is mounted with (4) #10 (3/16") fasteners on 2 7/8" (vertical) x 1 1/8" (horizontal) hole centers. As used on some J/24’s.
|
|
|
|
|
| Stainless Steel Exit Block: K-11199P:
Internal SS Exit Block is used for halyards, spinnaker pole lifts and other control lines. Plastic sheave (K-8850) is 1 7/8" diameter x 9/16" wide and will handle line up to 7/16" diameter. Assembly fits in mast cutout 2 3/8" high x 13/16" wide and projects 2 1/4" inside of mast. Mounting flanges are 2 3/8" high x 2" wide, and are at 90 degrees to the sheave for use on flat surfaces; flanges can also be bent to fit a variety of curved surfaces. Assembly is mounted with (4) #10 (3/16") fasteners on 1 7/8" (vertical) x 1 1/2" (horizontal) hole centers.
|
|
| Stainless Steel Exit Block: K-11199P-1:
As K-11199P, above, but mounting flanges already angled for use on curved surfaces. Flanges can be bent more or less, to fit a variety of curved surfaces.
|
|
| Stainless Steel Exit Block: K-11199A:
Internal SS Exit Block is used for halyards, spinnaker pole lifts and other control lines. Aluminum sheave (K-10861-1) is 2" diameter x 9/16" wide and will handle 3/16" wire, or rope up to 1/2" diameter. Assembly fits in mast cutout 2 3/8" high x 13/16" wide and projects 2 1/4" inside of mast. Mounting flanges are 2 3/8" high x 2" wide, and are at 90 degrees to the sheave for use on flat surfaces; flanges can also be bent to fit a variety of curved surfaces. Assembly is mounted with (4) #10 (3/16") fasteners on 1 7/8" (vertical) x 1 1/2" (horizontal) hole centers. Unit now features removable sheave.
|
|
| Stainless Steel Exit Block: K-11199A-1:
As K-11199A, above, but mounting flanges already angled for use on curved surfaces. Flanges can be bent more or less, to fit a variety of curved surfaces. Unit now features removable sheave. |
|
~ Home ~
