 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
|
1 1/8" OD Round Spreaders & Hardware |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
|
1 1/8" OD Round Spreaders & Hardware |
|
|
|
|
| Kenyon Spars 1 1/8" Round Spreader Section Measurements: 1.125" OD x .875" ID (1 1/8" x 7/8") Wall Thickness: .125" Weight/ft.: .472 lbs. Moments of inertia: Ixx = Alloy: 6063-T5 Stock Length: 21' Common Mast usage: Kenyon E, 3049, 3550, 3650 and similar Mast Sections. |
 |
| Common Boat usage:
Buccaneer 270; DM 22; Hunter 25; Lancer 25; North American NA23; O'Day 23, 25, 32K Mizzen;
Paceship Yachts PY 23; Reinell 26; S2 7.3, 23; San Juan 26; and hundreds of others. |
|
|
|
| 1 1/8" OD Round Spreaders & Hardware | |
| 1 1/8" Outside Diameter (OD) Heavy-Wall Round Spreaders on Kenyon Spars have been used with a variety of Spreader Bases. To order 1 1/8" OD Heavy Round Replacement Spreaders you must know the Length of the Spreader, from inboard end to the slot in the tip. | |
|
|
|
|
1 1/8" OD Spreader Tube x 2'6" (30"): K-1412TC-30:
1 1/8" OD Spreader Tube x 3' (36"): K-1412TC-36: 1 1/8" OD Spreader Tube x 3'6" (42"): K-1412TC-42: 1 1/8" OD Spreader Tube x ___: K1412TC-___: 1 1/8" OD x 7/8" ID Heavy-Wall Round Spreader Section is stocked in a clear anodized finish and is available in a variety of Standard lengths, or others up to 21'. To order: specify length.
|
 |
|
1 1/8" OD Spreader Ass'y x 2'6" (30"): K-1412A-30:
1 1/8" OD Spreader Ass'y x 2'9" (33"): K-1412A-33: 1 1/8" OD Spreader Ass'y x 3' (36"): K-1412A-36: 1 1/8" OD Spreader Assembly x ___: K-1412A-___: 1 1/8" OD Heavy-Wall Round Spreader Assembly is supplied without holes for attachment to Mast Bracket. Spreader attaches to various Mast Brackets with different hole spacing, hole must be drilled on-site for attachment to Mast Bracket. Outboard end, K-9896, has slot for shroud up to 3/16" diameter, and hole for seizing wire (included). Assemblies can be cut to shorter lengths. To order: specify length from inboard end to the slot in the tip.
|
|
|
|
|
|
Spreader Tip for 1 1/8" OD x 7/8" ID Spreader: K-9896:
Clear anodized Aluminum Spreader Tip for 1 1/8" OD x 7/8" ID Spreader has slot for up to 3/16" diameter shroud. Lightweight, compact version replaces earlier Cast style and features cross-hole for seizing wire. New-style turned Tip extends shroud seat 5/16" beyond spreader tube, unit projects 5/8" (maximum) beyond spreader tube and is carefully rounded to reduce sail chafe.
|
|
|
Spreader Boot Pair for 1 1/8" OD Spreader: SP-057B:
Spreader Boot for 1 1/8" OD Spreader is designed to reduce sail chafe. White Rubber Boot is attached to Spreader and Shroud using wire ties or Rigging Tape. Sold in Pairs only, they are (maximum) 5 3/4" long.
|
|
|
|
|
| Spreader Bases for 1 1/8" OD Round Spreaders | |
|
Listed below are the Spreader Bases most commonly used with 1 1/8" OD Round Spreaders.
Some earlier versions are available, Please specify Mast Section and angle aft. Some Spreader Bases are commonly used with Compression Tubes fitting over one or more mounting bolts, See Compression Tubes. |
|
|
Round Spreader Base Ass'y for 1 1/8" Spreaders: K-968:
SS welded Spreader Bracket Assembly is used on Kenyon E-Section, 3049, 3550, 3650, and similar Mast Sections. Formed plate has welded socket to fit Kenyon 1 1/8" OD Round Spreaders. Teardrop shaped plate measures (maximum) 3 3/8" high x 2 1/2" wide, socket projects 2 1/4" (maximum) out from mast wall. Attaches to the mast with (7) 3/16" (#10) screws or rivets and (1) 3/8" bolt that also fastens the lower shroud tang. Spreader is held in socket using vertical 3/16" screw and nut or cotter pin. Used for rigs with in-line spreaders, base has 5-degree vertical lift. D40429 |
|
~ Back to Spreaders Main Page ~
~ Home ~