|
|
| Spartan Spars 1 1/4" Round Spreader Section - SP-090 Measurements: 1 1/4" OD x 1" ID Wall Thickness: .125" Weight/ft.: .519 lbs. Alloy: 6061-T6 Stock Length: 12' Common Boat usage: Cape Dory 27*, 28*, 30*; |
|
|
|
|
| 1 1/4" OD Round Spreader Tube | |
|
1 1/4" Round Spreader Tube x 3' 1": SP-090TC-37:
1 1/4" Round Spreader Tube x 4': SP-090TC-48: 1 1/4" Round Spreader Tube x __: SP-090TC-___: Spartan 1 1/4" OD x 1" ID Spreader Tube (SP-091) is stocked in a clear anodized finish and is available in a variety of Standard lengths, or any length up to 18'. To order: specify length. |
|
|
|
|
| 1 1/4" OD Round Spreader Assemblies & Parts | |
|
1 1/4" Round Spreader Ass'y x 37 1/2" long: SP-090AS:
1 1/4" Round Spreader Ass'y x 48 1/2" long: SP-090A-48: 1 1/4" Round Spreader Assembly x __: SP-090A-__: Spartan SP-090 Spreader is 1 1/4" OD x 1" ID, and has Aluminum Tip, SP-090T, with hole for seizing wire (included). Clear anodized 1 1/4" Spreader Assemblies are 5/8" (overall) longer than mast to wire measurement. Available in a variety of Standard lengths, or any other length. To order: specify maximum length from inboard end to shroud bearing surface.
|
|
|
|
|
|
1 1/4" Round Spreader Tip: SP-090T:
Clear anodized Aluminum Spreader Tip for 1 1/4" OD x 1" ID Spreader features slot for up to 5/16" (8mm) shroud. Lightweight, compact version replaces earlier Cast style and features cross-hole for seizing wire. New-style turned Tip extends shroud seat 1/2" beyond spreader tube, unit projects 1 1/16" (maximum) beyond spreader tube and is carefully rounded to reduce sail chafe. As K-8609. cast was 3/4",1 3/8"
|
|
|
Spreader Tip for Tapered Spreader (1 1/4" OD Outboard): K-10127: Aluminum Spreader Tip for Kenyon Swaged Taper Spreader fits Spreader End that has been reduced to 1 1/4" OD x 7/8" ID. Cast Spreader Tip has slot for up to 9/32" diameter shrouds and features cross-hole for seizing wire. This part is no longer available and is shown here for identification only. The SP-090T, above, can be used by filing the spreader ID.
|
|
|
Spreader Boot Pair for 1 1/4" OD Spreader: SP-057B:
Spreader Boot for 1 1/4" OD Spreader is designed to reduce sail chafe. White Rubber Boot is attached to Spreader and Shroud using wire ties or Rigging Tape. Sold in Pairs only, they are (maximum) 5 3/4" long.
|
|
|
|
|
| Spreader Bases for 1 1/4" Round Spreaders | |
|
Listed below are Spreader Bases commonly used with 1 1/4" OD Round Spreaders.
Some Spreader Bases are commonly used with Compression Tubes fitting over one or more mounting bolts,
See Compression Tubes.
|
|
|
CD-4 Spreader Base - Triangular: SP-089: Triangular Cast aluminum Spreader Base for 1 1/4" Spreader fits CD-4 and RR#8 Mast Sections. Attaches to Mast with (3) 1/4" FH machine screws and a 3/8" bolt. Unique and sleek design allows for use of the same 3/8" bolt as an attachment point for a lower shroud tang, SP-205. Used for rigs with in-line spreaders, base has 5-degree vertical lift. Please Note: If ordering this item as a replacement part, please verify OD of Spreaders as early units, SP-089LX, were produced for 1 5/16" OD Spreaders.
|
 |
|
CD-4 Spreader Base - Square: SP-089-0: Older style, Square Cast aluminum Spreader Base for 1 1/4" Spreader fits CD-4 and RR#8 Mast Sections. Attaches to Mast with (4) 1/4" RH machine screws and a 3/8" bolt. Design allows for use of the same 3/8" bolt as an attachment point for lower shroud tang, SP-205. Used for rigs with in-line spreaders, base has 5-degree vertical lift. Please Note: If ordering this item as a replacement part, please verify OD of Spreaders as early units were produced for 1 5/16" OD Spreaders. S55-34 |
 |
~ Back to Spreaders Main Page ~
~ Home ~
