Spartan 1 5/16" OD Spreader Section

1 5/16" OD Round Spreader Tube
*1 5/16" Round Spreader Tube x 37": SP-091TC-37:* *1 5/16" Round Spreader Tube x 48": SP-091TC-48:* *1 5/16" Round Spreader Tube x ___: SP-091TC-___:* Spartan 1 5/16" OD x 1 1/16" ID Spreader Tube (SP-091) is stocked in a clear anodized finish and is available in a variety of Standard lengths, or any length up to 19'. To order: specify length.

1 5/16" OD Round Spreader Assemblies & Parts
*1 5/16" OD Spreader Ass'y w/ Standard Tip x 37 1/2": SP-091AS:* *1 5/16" OD Spreader Ass'y w/ Standard Tip x 42": SP-091A-42:* *1 5/16" OD Spreader Ass'y w/ Standard Tip x 48": SP-091A-48:* *1 5/16" OD Spreader Ass'y w/ Standard Tip x ___: SP-091A-___:*
Standard Spartan SP-091 Round Spreader is 1 5/16" OD x 1" ID x 37 1/2" long (mast to wire) and has Aluminum Tip, *SP-091T, with slot for upper shroud, and hole for seizing wire (included). SP-091A-42* was used on Bristol 27, 29.9, and others. Finished spreaders are available in a variety of Standard lengths, or any other length, standard finish is clear anodized. To order: specify maximum length from inboard end to shroud bearing surface.
*1 5/16" OD Spreader Ass'y w/ Twist-Lock Tip x 37 1/2": SP-091ATLS:* *1 5/16" OD Spreader Ass'y w/ Twist-Lock Tip x 42": SP-091ATL-42:* *1 5/16" OD Spreader Ass'y w/ Twist-Lock Tip x 4': SP-091ATL-48:* *1 5/16" OD Spreader Ass'y w/ Twist-Lock Tip x ___: SP-091ATL-___:*
Spartan SP-091 Round Spreader with Twist-lock Tip, SP-091TL, is 1 5/16" OD x 1 1/16" ID and has special Aluminum Tip which secures Shroud without the use of seizing wire. As Spartan SP-091AS, above, but with special 'twist-lock' Tip. Finished spreaders are available in a variety of Standard lengths, or any other length, standard finish is clear anodized. To order: specify maximum length from inboard end to shroud bearing surface.

*1 5/16" OD Round Spreader Tip: SP-091T:* Clear anodized Aluminum Spreader Tip for 1 5/16" OD x 1 1/16" ID Spreader features slot for up to 5/16" (8mm) shroud. Lightweight, compact version replaces earlier Cast style and features cross-hole for seizing wire. New-style turned Tip extends shroud seat 1/2" beyond spreader tube, unit projects 1 1/8" (maximum) beyond spreader tube and is carefully rounded to reduce sail chafe.
*1 5/16" OD Round Spreader Tip: SP-091TX:* Old-style Cast aluminum Spreader Tip for 1 5/16" OD x 1 1/16" ID Spreader features slot for up to 1/4" diameter shroud. Shroud is secured to Tip with seizing wire. Tip extends shroud seat 1 1/8" beyond spreader tube, unit projects 1 7/16" (maximum) beyond spreader tube. This item is no longer available, having been replaced by the SP-091T, above.	SP-091TX
*1 5/16" OD Round Twist-lock Spreader Tip: SP-091TL:* Improved Spreader Tip for 1 5/16" OD x 1 1/16" ID Spreader features a special 'twist-lock' design, and a smooth, broad end to minimize sail chafe. Shroud is secured without seizing wire, by inserting it horizontally into Spreader Tip and then 'twisting' it to lie in line with the mast. Tip accommodates shrouds up to 9/32" diameter and extends shroud seat 1/2" beyond spreader tube. Cast clear anodized aluminum Spreader Tip projects 1 1/16" (maximum) beyond spreader tube and is carefully rounded to reduce sail chafe.
Spreader Boot Pair for 1 5/16" OD Spreader: SP-057B: Spreader Boot for 1 5/16" OD Spreader is designed to reduce sail chafe. White Rubber Boot is attached to Spreader and Shroud using wire ties or Rigging Tape. Sold in Pairs only, they are (maximum) 5 3/4" long.

Spreader Bases for 1 5/16" Round Spreaders
Spartan 1 5/16" Round Spreaders are normally used with Spreader Bases which are formed to fit specific Mast Sections. Most Spreader Bases used with these Spreaders are specific to individual Mast Sections and are listed under the Mast Sections that they attach to, See Spartan Mast Sections. Others are listed below. Some Spreader Bases are commonly used with Compression Tubes fitting over one or more mounting bolts, See Compression Tubes.
*Cast Spreader Base - Rectangular, Small: PP SBR-2027S:* Rectangular Spreader Base for 1 5/16" OD Spreader. Anodized Cast Aluminum Spreader Base attaches to Mast with (2) 1/2" bolts on 3 11/16" (or 3 3/4") centers, lower bolt is also used to attach lower shroud Tang(s). Spreader is held in socket by 1/8" cotter Pin (included). Unit is 5 1/2" long x 2" wide, base is slightly contoured for use with a variety of Mast Sections. As used on Pearson 22, Ensign, Electra; Bristol 22, 24 and others. Unit also replaces old-style Male Spreader Base which was 5 1/4" x 2" with 1/2" holes on 3 3/8" centers.
*Cast Spreader Base - Rectangular, Large: PP SBR-2018L:* Rectangular Spreader Base for 1 5/16" OD Spreader. Anodized Cast Aluminum Spreader Base attaches to Mast with (2) 1/2" bolts on 4" centers, lower bolt is also used to attach lower shroud Tang(s). Spreader is held in socket by 1/8" cotter Pin (included). Unit is 6" long x 3" wide, base is slightly contoured for use with a variety of Mast Sections. As used on Pearson 26, Ariel, Commander, Renegade, Triton; and Bristol 26, 27, 29, 30, and others.

*1" Round Spreader Bar w/ Shroud Tang - C&C 24: CC SPBR-24:*
Aluminum Spreader Bar for 1 5/16" OD Spreader features integral slots for single Lower Shrouds using 3/16" AN (MS) Eyes. Round, anodized Spreader Bar is (maximum) 1" OD x 6 1/4" long, with 5/16" pin holes and is specially machined to allow a 5-degree vertical lift and accommodate lower shrouds. Designed for use with a 4" wide Mast. As used on C&C 24.
*1" Round Spreader Bar w/ Shroud Tang - C&C 26: CC SPBR-26:*
Aluminum Spreader Bar for 1 5/16" OD Spreader features integral slots for single Lower Shrouds using 7/32" AN (MS) Eyes. Round, anodized Spreader Bar is (maximum) 1" OD x 6 3/4" long, with 5/16" pin holes and is specially machined to allow a 5-degree vertical lift and accommodate lower shrouds. Designed for use with a 4 1/2" wide Mast. As used on C&C 26.

Your cart

Spars, Rigging, and Hardware for Sailboats

Spartan Spars 1 5/16" Round Spreader Section - SP-091 Measurements: 1 5/16" OD x 1 1/16" ID Wall Thickness: .133" Weight/ft.: .581 lbs. Alloy: 6061-T6 Stock Length: 19' Common Boat usage: Bristol 22, 24, 26, 27, 29, 29.9, 30; C&C 24, 26; Cape Dory 25D, Cape Dory 26, Cape Dory 27, Cape Dory 28, Cape Dory 30*; Pearson 22, 26, 27, 28, Electra, Ensign, Triton, and others.