Kenyon E Boom Old-style Internal Gooseneck

Note: Kenyon Internal Gooseneck Assemblies are now equipped with the new friction-lock lever-action cams for greater holding ability, and SS cover plates to keep the reef lines captive at all times. Old-Style units featured Spring Cams (with or w/o handles), and different reef sheaves than the improved version. The Old-Style units are easily identified by the absence of the SS cover plates. While upgrading to the improved style using one of the K-11443 Conversion Kits (below) is recommended, original parts for the Old-Style gooseneck are still available, below.

*E-section Internal Gooseneck Casting - Old-Style: K-10364X:* Replacement casting is identical to K-10364, but has extra holes drilled for use with Old-Style Spring-Cam assemblies and sheaves listed below. Casting extends 5" (maximum) forward of the boom tube. Distance from horizontal Pin hole to boom tube is 4 3/8".
*Reefing Sheave for Old-Style E-section Gooseneck: K-10358:* Molded Nylon sheave w/ integral Bronze bushing is 1 1/16" OD x 35/64" (<9/16") wide x 3/8" ID.
*Reefing Sheave/Cam Axle for Old-Style E-section Gooseneck: K-10379:*
SS axle pin is 3/8" dia. x 2.40" grip, with a turned groove on each end to accept 3/8" SS Snap Rings, K-63015 (2 included).
*Outhaul Sheave for E-section Gooseneck: K-198-7A:* Anodized aluminum sheave is 1 3/4" OD x 31/64" wide x 3/8" ID.
*Outhaul Sheave Axle for E-section Gooseneck: K-10380:* SS axle pin is 3/8" dia. x 1" grip, with a turned groove on each end to accept 3/8" SS Snap Rings, K-63015 (2 included).
SS Snap Rings for 3/8" Axle Pin: K-63015-2P: In 2-pack. Require small snap ring pliers for attachment.
*Reef Cam Assembly for Old-Style Gooseneck - Port: K-GNCA-P:* *Reef Cam Assembly for Old-Style Gooseneck - Starboard: K-GNCA-S:*
Extruded aluminum Spring-Cam assembly fits on 3/8" pin and includes Cam, SS spring, and molded nylon insert.
*Reef Cam Ass'y w/ handle for Old-Style Gooseneck - Port: K-GNCAH-P:* *Reef Cam Ass'y w/ handle for Old-Style Gooseneck - Starboard: K-GNCAH-S:*
Extruded aluminum Spring-Cam assembly with handle fits on 3/8" pin and includes Cam, SS spring, and molded nylon insert. As K-GNCA-P, and S (above), but cam incorporates a SS handle. Specify Port or Starboard.

Double Reef Cam Conversion Kit for E-Section Gooseneck: K-11443:
Cam Conversion Kit for E-Section Internal Gooseneck converts Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Easily installed Kit includes everything necessary for 2 reef lines including Cam levers, adjustable friction washers, reef sheaves, SS spacers, Cover plates, bolts and locknuts. No machining is required. Individual components are listed separately, See Parts for New-Style E-Section Internal Gooseneck Assembly.
*Port Reef Cam Conversion Kit for E-Section Gooseneck: K-11443P:* *Starboard Reef Cam Conversion Kit for E-Section Gooseneck: K-11443S:*
Single Cam Conversion Kit for E-Section Internal Gooseneck converts Old-Style Spring-Cam arrangement to the New-Style friction cam assembly. Easily installed Kit includes everything necessary for single reef line including Cam lever, adjustable friction washers, reef sheave, SS spacer, Cover plate, bolts and locknuts. No machining is required. Specify Port or Starboard. Individual components are listed separately, See Parts for New-Style E-Section Internal Gooseneck Assembly.
Sheave Only Conversion Kit for E-Section Internal Gooseneck: K-11443NC:
Sheave Conversion Kit for E-Section Internal Gooseneck converts Old-Style Gooseneck to the New-Style with Cover Plates, Sheaves, and No cams. Easily installed Kit includes everything necessary for leading reef lines down and aft, including (2) reef sheaves, (4) SS spacers, Port and Starboard Cover plates, bolts and locknuts. No machining is required. Individual components are listed separately, See Parts for New-Style E-Section Internal Gooseneck Assembly. As K-11443, above, but with (2) SS Spacers to replace the reef cams.

Your cart

Spars, Rigging, and Hardware for Sailboats