Rig-Rite 8349 Mast Section


RR #8349 Mast Section RR #8349 Mast Section - Clear Anodized: RR-X8349CA-___: RR #8349 Mast Section - Raw: RR-X8349R-___: Rig-Rite #8349 Section Mast Tube is stocked in a variety of lengths (listed above) fully anodized or raw (mill finish), it can also be cut to shorter lengths. To order, specify length. Sections can also be milled for the sailgate or other components, painted finishes and other lengths are available on special order, Please specify. If you require a complete Mast Assembly, you can select from components below and contact us with specifications.

RR #8349 Standard Mast Hardware Listed below are parts specific to the Rig-Rite #8349 Mast Section. For more generic parts, see categories listed under Spar Parts. There are many parts for specific configurations that are not listed here. If you require Rig-Rite #8349 Mast Components not listed here please contact us with details.

*Inset Masthead Assembly for Masthead Rig: RR 8349M-H1:* Bolt-in aluminum Masthead Assembly for RR #8349 Mast Section incorporates (4) 2 3/4" OD aluminum sheaves, PP S11A9-8RR, for internal or external wire or rope halyards, and (2) 5/8" Pins for Headstay and Backstay attachment. Includes 1/4" Clevis Pin for topping lift attachment and lugs for Dual Offset Spinnaker Bails using standard 5/16" shackles (order separately). Masthead fits in 4" deep x 1 3/4" wide slot cut into fore and aft sides of the mast tube. Masthead Assembly is 10 1/2" long x (maximum) 5 1/4" wide, and attaches to the mast with (1) 1/2" bolt. As used on Sabre 42.

Spreaders The Rig-Rite #8349 Mast Section is normally used with RR SP275T, and RR SP450T Airfoil Spreaders, and appropriate Spreader Bars, listed below. For Spreader details, or to order replacement Spreaders, See Rig-Rite Spreader Sections.
*SP275T Spreader Bar for 8349 Mast w/ -10 Rod In-line Shrouds: RR 8349M-275B-10R:*
Aluminum Spreader Bar for RR #8349 Mast is used with Rig-Rite SP275T Spreaders for rigs with in-line shrouds using standard -10 Rod Stemballs. Installed through a 1 3/4" x 5/8" slot in the mast, Spreaders fit over the Bar and are pinned straight through the Bar, holding the Bar and Spreaders in place. Bar features captive SS rods to eliminate chafe from halyards or mast wall. Unit is 15" long x 1 3/4" wide x 5/8" high, and has a 5-degree vertical lift. Also suitable for use on other 5" wide Mast Sections. As used on Sabre 42 (upper). SP275B Spreader Bars are available in a variety of other configurations to accommodate other wire or rod stemballs, and to fit different Mast Sections, See Rig-Rite SP275T Spreader Section.
*SP450T Spreader Bar for 8349 Mast w/ -12 Rod Lower Shrouds: RR 8349M-450B-12R2:*
Aluminum Spreader Bar for RR #8349 Mast is used with Rig-Rite SP450T Spreaders for rigs with fore and aft lower shrouds using standard -12 Rod Stemballs. Installed through a 3" x 1" slot in the mast, Spreaders fit over the Bar and are pinned straight through the Bar, holding the Bar and Spreaders in place. Bar features captive SS rods to eliminate chafe from halyards or mast wall. Unit is 15" long x 3" wide x 1" high, and has a 5-degree vertical lift. Also suitable for use on other 5" wide Mast Sections. As used on Sabre 42 (lower). SP450B Spreader Bars are available in a variety of other configurations to accommodate other wire or rod stemballs, and to fit different Mast Sections, See: Rig-Rite SP450T Spreader Section.

*3/4" Sail Slide Stop: K-10424:* SS Spring Pin Sail Slide Stop fits all mast sections with track for 3/4" internal flat slides. Superior design allows Slide Stop to remain captive in mast track. Gate cutout (1 3/4" high) is made just 1" above SS Gooseneck bracket. Spring pin fits in 1/4" hole drilled at top of cutout, unit slides down beneath Gooseneck Bracket when Spring pin is pulled. This design allows sail slides to come as close as possible to the gooseneck while remaining in track, and eliminates problems associated with slides snagging while going past a normal sail gate. Unit is 2 1/2" long x 3/4" wide with a 1/4" spring pin. 74-66
8349 Gooseneck Bracket for 2 1/2" Toggle: RR 8349M-GB1: SS Gooseneck Bracket for RR #8349 Mast Section has 1/2" vertical Pin hole, for use with standard Gooseneck Toggle up to 2 1/2" high. Base is 5" vertical x approximately 4 3/4" wide, and attaches to the mast with (10) 1/4" RH fasteners. Commonly used with Combination Toggle/Tack/Reef Hook Assembly, RR 45-148MRA, below. Can also be used as Vang Bracket with addition of Vang Toggle.
	Vertical Gooseneck Pin: CP8-104A: SS Gooseneck Vertical Pin for use with Gooseneck Bracket, *RR-8349M-GB1.* SS Clevis Pin is 1/2" diameter x 3 1/4" grip length. Assembly includes (4) nylon bearing washers and cotter pin. 2L,2S
Gooseneck Toggle Ass'y w/ Tack & Reef Hooks: RR 45-148MRA: Combination Toggle/Tack/Reef Hook assembly features SS Tack/Reef Hook bolted to Aluminum Toggle (RR 45-148M) and includes 1/2" Tack fastpin, *K-10718.* Toggle takes *1/2" vertical and* horizontal pins. Anodized Toggle is 2 5/16" high x 1 3/8" wide (15/16" wide @ Horizontal pin hole) x 3 7/8" (maximum) long, pin holes are on 2 1/2" centers. Toggle fits a variety of Mast Brackets designed for a 2 5/16" Toggle with a 1/2" vertical pin. As used on Sabre 42**, and others. RR 8349M-GTA
	Gooseneck Toggle w/ Recess - 2 1/4" High: RR 45-148M: Machined Aluminum Gooseneck Toggle is 2 1/4" high with holes for *1/2" vertical and* horizontal pins.** Anodized Toggle is 2 1/4" high x 1 1/4" wide (15/16" wide @ Horizontal pin hole) x 4" (maximum) long, pin holes are on 2 1/2" centers. Toggle features 2nd 1/2" vertical hole (1 5/8" aft) with milled Recess for non-pivoting attachment of Tack/Reef Hook assembly, PP 54-22S. Toggle fits a variety of Mast Brackets and Gooseneck Slides designed for a 2 1/4" Toggle with a 1/2" vertical pin. Replaces earlier Cast version. As used on Sabre 42, and others.
	SS Reef Hook/Tack Ass'y for 1/2" Vertical Bolt: PP 54-22S: Heavy-duty Stainless Steel Reef Hook/Tack Assembly mounts under head of 1/2" Vertical Bolt. Dual Reef Hook Assembly is 3 1/4" wide (at top), 1 3/8" wide (at bottom), 3 1/4" high, and has 1" clearance for Tack. Assembly is formed from 1" x 3/16" SS Strap and includes 1/2" SS Tack Fastpin, K-10718.

Vang Bracket for Rigid Vang – Special: A variety of semi-custom Brackets, or Bracket/Toggle combinations are available to fit rigid (or solid) vangs produced by a number of manufacturers. Please specify vang manufacturer, model and size.
Electrical Access Plate: RR 72-99: Electrical Access Plate is designed to allow access to internal electrical plugs above the mast step, without having to unstep the mast. Saves much in frustration and money by allowing you to check mast wiring connections with the mast up. SS Plate is 4 1/2" x 2" and is designed to cover a 3" x 1 1/4" vertical slot in the side of the mast, just above the top of the mast step. Plate is slightly curved to fit a variety of mast sections and attaches with (4) 1/4-20 RH machine screws (included).
Keel-Mount Mast Step: RR 8349M-KS: Mast Step for RR #8349 Mast Section fastens to keel or keelson with (4) 3/8" bolts in external adjustment slots to allow for precise positioning without unstepping the mast. Special design incorporates rocker to allow greater Mast control, and drainage channel to prevent water build-up inside the mast. Mast Step measures 9 7/8" long x 8" wide, and allows for 2 5/8" fore and aft adjustment. Cast in 356 Aluminum with white Awlgrip finish. As used on Sabre 42.
Electrical Wire Slide: K-10908: Electrical Wire Slides - 10 Pack: K-10908P: Nylon slides fits all Kenyon and Rig-Rite mast sections with internal electrical wire slide tracks. Slides are attached to wiring harness at 2-3 foot intervals with tie wraps. Prevents wires from slapping, and from fouling internal halyards.

Your cart

Spars, Rigging, and Hardware for Sailboats