Spinnaker Cars for Recirculating Ball Tracks

These Spinnaker Cars are designed to fit on a variety of Recirculating Ball (RCB) Tracks, and are held in place on the track by means of a line control system. The use of these Ball-Bearing Cars (on special Tracks) minimizes friction on the Track, allowing for greater ease of movement under load. These Spinnaker Cars are shipped on a short length of loading Track which keep the Ball-Bearings in place until Car is loaded on destination Track. Cars must not be removed from Track, as doing so will allow the Ball-Bearings to escape - rendering the Car inoperative as well as making a mess! Loading Track should be saved for future Car removal or service. All Cars include shackles or other attachments for Control Lines or Blocks. Ring Cars are used for Poles with standard Piston or Trigger pole ends, Pin, or Bell Cars are used to fit the variety of special inboard Spinnaker Pole Ends available. Please note that Ring Cars are not designed for, or recommended for vertical pole stowage applications. See also, Spinnaker Poles and Parts, OR, Back to Spinnaker Car Main Page.

Spinnaker Cars for Ball-Bearing (RCB) Tracks For Sparcraft/Facnor/Lewmar Size 2 (30mm (1 3/16") wide) Track For Harken Small Boat (7/8" (22mm) wide) Track (#373, or #2720) For Harken Midrange (1 1/16" (27mm) wide) Track (#1602, or #1616) For Harken Big Boat (1 1/4" (32mm) wide) Track (#516, or #758) For Nicro-Fico NF 1100 Track For Z-Spar RCB (Add-on) Tracks (separate page)

Spinnaker Cars for Sparcraft/ Facnor/ Lewmar Track
Sparcraft/ Facnor/ Lewmar Size 2 Recirculating Ball (RCB) Track measures 30mm (1 3/16") across the top. Facnor Size 2 Cars use 5/16" (8mm) Torlon Balls.
Spinnaker Car w/ Large Bell for Facnor Size 2 RCB Track: FM 30B-B120F:
Recirculating Ball Spinnaker Car with Metric Large Bell to fit Sparcraft/ Facnor Size 2 RCB Track. Car includes blocks for 2-1 control line purchase and Francespar/ Sparcraft Large Bell fitting with special Toggle, Large Bell fitting is compatible with spinnaker poles using Francespar or Barbarossa/ Harken inboard Large Bell Pole Ends. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, See: Metric Spinnaker Poles & Parts. Machined Car Body is (maximum) 5 9/16" (140mm) long x 3 3/16" (81mm) wide, Car uses (64) 5/16" Torlon Balls.
Spinnaker Car w/ Toggle only for Francespar/ Sparcraft Large Bell: FM 30B-BFT:
Recirculating Ball Spinnaker Car with Toggle only for Francespar/ Sparcraft Large Bell fits Sparcraft/ Facnor Size 2 RCB Track and includes Shackles for Towing line.
	*Francespar Large Bell w/ Toggle for Ball-Bearing Car: FM 30B-B120F-BTA:*
	Replacement Francespar/ Sparcraft Large Bell & Toggle Assembly for use with FM 30B-B120F Recirculating Ball Spinnaker Car. Toggle has hole for 8mm vertical Pin and is 1 1/2" (37mm) high, Francespar/ Sparcraft Large Bell fitting is compatible with spinnaker poles using Francespar or Barbarossa/ Harken inboard Large Bell Pole Ends, See: Metric Spinnaker Poles & Parts.
	*Francespar Large Bell only w/o Toggle: FSP B-120-NT:* Francespar/Sparcraft Large Bell only as in FM 30B-B120F-BTA, above. Large Bell fitting includes Trigger and 12mm horizontal Pin for attachment to Francespar/ Sparcraft Toggles.
	*Toggle only for Ball-Bearing Car: FM 30B-B120F-T:* Replacement Toggle only for *FM 30B-B120F* Recirculating Ball Spinnaker Car. Special Extruded Aluminum Toggle (with Bushings) is 1 1/2" (37mm) high x 1 9/16" (40mm) wide x 81mm long, with an 8mm hole for attachment to Spinnaker Car, and a 12mm hole for attachment to Francespar/ Sparcraft Large Bell fitting.
	Replacement Balls for Francespar Ball-Bearing Spinnaker Car: FM 30B-B120F-BP:
	Replacement Ball Bearing Pack for Facnor Size 2 Spinnaker Car. Pack includes (64) 5/16" Torlon Balls, for use with *FM 30B-B120F* Car.
*Sparcraft/ Facnor Size 2 Spinnaker Track: FMT2x__:* *Sparcraft/ Facnor Size 2 Spinnaker Track: FMT2x3.4M:* Sparcraft/ Facnor/ Lewmar Size 2 RCB Track (F40). Size 2 Recirculating Ball Spinnaker Track is 30mm (1 1/8") wide x 18mm high and fastens to Mast with 8mm (5/16") FH on 100mm (4") centers. Available in lengths up to 3400mm (11' 2").
*Sparcraft Size 2 Spinnaker Track Control End: Lew BBT2-CE:* Control End with Sheave and Becket is used with Sparcraft/ Facnor Size 2 RCB Spinnaker Track. Machined Aluminum Control End is (maximum) 1 3/8" wide x 3 3/4" long (35 x 94mm), and attaches to Mast with (2) 5/16" FH on 1 3/4" centers, with one screw going through the Track. Molded Sheave is 1 1/4" OD x .60" wide x 7/16" ID. 29172015

Spinnaker Cars for Harken Small Boat Track
Harken Small Boat Recirculating Ball (RCB) Track measures 7/8" (22mm) across the top. Harken Small Boat Cars use 1/4" Torlon Balls.
Spinnaker Ring Car for Harken Small Boat RCB Track: Har 780: Recirculating Ball Spinnaker Car to fit Harken Small Boat RCB Track. Car has cast SS Ring assembly screwed to extruded Aluminum Body. Car is 4 3/8" (110mm) long x 2 3/16" (56mm) wide, SS Ring is 3/8" x 1 1/4" ID, and projects 1 3/4" (maximum) from Track surface. Har 780 Car uses (64) 1/4" Torlon Balls.		R
	Replacement Balls for Harken Small Boat Spinnaker Car: Har 780-BP:
	Replacement Ball Bearing Pack for Harken Small Boat Spinnaker Cars. Pack includes (64) 1/4" Torlon Balls, for use with Har 780 Car.

Spinnaker Cars for Harken Midrange Track
Harken Midrange Recirculating Ball (RCB) Track measures 1 1/16" (27mm) across the top. Harken Midrange Cars use 5/16" Torlon Balls.
	Replacement Balls for Harken Midrange Spinnaker Cars: Har 781-BP:
	Replacement Ball Bearing Pack for Harken Midrange Spinnaker Cars. Pack includes (60) 5/16" Torlon Balls, for use with all standard Harken Midrange Spinnaker Cars (5 1/4" long).
Spinnaker Ring Car for Harken Midrange RCB Track: Har 781: Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track. Car has cast SS Ring assembly screwed to extruded Aluminum Body. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, SS Ring is 3/8" x 1 1/4" ID, and projects 1 3/4" (maximum) from Track surface. Har 781 Car uses (60) 5/16" Torlon Balls.		R

Spinnaker Car w/ TS Pin for Harken Midrange Track: Har 1580-TS: Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Forespar TS Pin & Toggle Assembly. TS Pin (1" OD x 3 5/8" long) fits all Forespar TS type Spinnaker Pole ends, See Spinnaker Poles & Parts. Extruded Aluminum Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Toggle projects 4 5/8" (maximum) from Track surface. Har 1580 Cars use (60) 5/16" Torlon Balls.
	Car only for Harken Midrange Track & TS Pin: Har 1580: Spinnaker Car only to fit Harken Midrange Track and Forespar TS Pin & Toggle Assembly. Extruded Aluminum Car includes 1/2" vertical Pin with 1" clearance for Forespar TS Pin & Toggle Assembly. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Pin center is 1 7/16" from Track surface. Har 1580 Cars use (60) 5/16" Torlon Balls. *As Har 1580-TS,* above, but without TS Pin & Toggle Assembly.
	*Forespar TS Pin & Toggle Ass'y for Spinnaker Car: For TS-PT:*
	Replacement Forespar TS Pin & Toggle Assembly fits all Forespar TS type Spinnaker Pole ends, and Spinnaker Cars with a 1/2" vertical Pin and clearance for a 1" Toggle. Stainless Steel TS Pin is 1" OD x 3 5/8" long, SS Toggle is 1" high with hole for a 1/2" Pin, and is 2 3/4" between Pin centers.

Spinnaker Car w/ Sparcraft Pin for Harken Midrange Track: Har 1579-SC:
Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Sparcraft Bayonet Pin & Toggle Assembly. Sparcraft Bayonet Pin (7/8" OD x 4" long, beneath head) fits all Sparcraft Bayonet type Spinnaker Pole ends, See Spinnaker Poles & Parts. Extruded Aluminum Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Toggle projects 3 3/4" (maximum) from Track surface. Har 1579 Cars use (60) 5/16" Torlon Balls.
	Car only for Harken Midrange Track & Sparcraft Pin: Har 1579: Spinnaker Car only to fit Harken Midrange Track and Sparcraft Bayonet Pin & Toggle Assembly. Extruded Aluminum Car includes 5/8" vertical Pin with 1 3/16" clearance for Sparcraft Bayonet Pin & Toggle Assembly. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Pin center is 1 9/16" from Track surface. Har 1579 Cars use (60) 5/16" Torlon Balls. *As Har 1579-SC,* above, but without Sparcraft Bayonet Pin & Toggle Assembly.
	Sparcraft Pin & Toggle Ass'y - 5/8" Pin: SPC 73-13PT-1: Replacement Sparcraft Bayonet Pin & Toggle (Type 1) Assembly fits all Sparcraft Bayonet type Spinnaker Pole ends, and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Assembly includes Sparcraft Bayonet Pin, SPC 73-13P, and SS Toggle SPC 73-12T1.
	*Sparcraft Bayonet Pin only: SPC 73-13P:* Replacement Sparcraft Bayonet Pin only, fits all Sparcraft Bayonet type Spinnaker Pole ends. Stainless Steel Sparcraft Bayonet Pin is 7/8" OD x 4" long (beneath head), head is 9/16" thick with hole for 1/2" pin. Unit is (maximum) 5 3/4" long.
	*Sparcraft Type 1 Toggle only: SPC 73-12T1:* Replacement Sparcraft Toggle (Type 1) fits Sparcraft Bayonet Pin and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Stainless Steel Toggle is 1 3/16" high x 1 3/8" wide with holes for 5/8" (Vertical) and 1/2" (Horizontal) Pins, and measures 1 5/8" between Pin centers. Horizontal (1/2") Pin is included.

Spinnaker Car w/ Small Bell for Harken Midrange Track: Har 1578-MBS:
Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Metric Small Bell Fitting (B-130). Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD. Metric Small Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end, See Metric Spinnaker Poles & Parts. Extruded Aluminum Car is 5 1/4" (132mm) long x 2 3/4" (70mm) wide. Har 1578 Cars use (60) 5/16" Torlon Balls.
Spinnaker Car w/ Large Bell for Harken Midrange Track: Har 1578-MBL:
Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Metric Large Bell Fitting (B-120). Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD. Metric Large Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 70, 80 and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end, See Metric Spinnaker Poles & Parts. Extruded Aluminum Car is 5 1/4" (132mm) long x 7/8" wide. Har 1578 Cars use (60) 5/16" Torlon Balls.
	Car only for Harken Midrange Track & Bell Fitting: Har 1578: Spinnaker Car only to fit Harken Midrange Track and Harken/ Barbarossa Metric Bell Fittings. Extruded Aluminum Car includes 12mm vertical Pin with clearance for Harken/ Barbarossa Metric Bell Fittings, B-120, and *B-130.* Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Pin center is 1 3/8" from Track surface. Har 1578 Cars use (60) 5/16" Torlon Balls. As Har 1578-MBS, and Har 1578-MBL, above, but without Bell Fitting and Toggle. PC
	*Metric Small Bell & Toggle only: Har B-130:* Replacement Metric Small Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa/ Harken inboard Small Bell Pole Ends. Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm Pin and is 1 3/8" (34mm) high. Metric Small Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. See Metric Spinnaker Poles & Parts. For Small Bell and Toggle Components, See Replacement Metric Bell Fittings.
	*Metric Large Bell & Toggle only: Har B-120:* Replacement Metric Large Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa/ Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 12mm Pin and is 1 3/8" (34mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. See Metric Spinnaker Poles & Parts.

Spinnaker Cars for Harken Big Boat Track
Harken Big Boat Recirculating Ball (RCB) Track measures 1 1/4" (32mm) across the top. Harken Big Boat Cars use 3/8" Torlon Balls.
	Replacement Balls for Harken Big Boat Spinnaker Cars: Har 782-BP:
	Replacement Ball Bearing Pack for Harken Midrange Spinnaker Cars. Pack includes (72) 3/8" Torlon Balls, for use with all standard Harken Big Boat Spinnaker Cars (7 1/4" long).

Spinnaker Car w/ TS Pin for Harken Big Boat Track: Har 784-TS: Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Forespar TS Pin & Toggle Assembly. TS Pin (1" OD x 3 5/8" long) fits all Forespar TS type Spinnaker Pole ends, See Spinnaker Poles & Parts. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Toggle projects 4 3/4" (maximum) from Track surface. Har 784 Cars use (72) 3/8" Torlon Balls.
	Car only for Harken Big Boat Track & TS Pin: Har 784: Spinnaker Car only to fit Harken Big Boat Track and Forespar TS Pin & Toggle Assembly. Extruded Aluminum Car includes 1/2" vertical Pin with 1" clearance for Forespar TS Pin & Toggle Assembly. Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Pin center is 1 9/16" from Track surface. Har 784 Cars use (72) 3/8" Torlon Balls. *As Har 784-TS,* above, but without TS Pin & Toggle Assembly.
	*Forespar TS Pin & Toggle Ass'y for Spinnaker Car: For TS-PT:*
	Replacement Forespar TS Pin & Toggle Assembly fits all Forespar TS type Spinnaker Pole ends, and Spinnaker Cars with a 1/2" vertical Pin and clearance for a 1" Toggle. Stainless Steel TS Pin is 1" OD x 3 5/8" long, SS Toggle is 1" high with hole for a 1/2" Pin, and is 2 3/4" between Pin centers.

Spinnaker Car w/ Sparcraft Pin for Harken Big Boat Track: Har 783-SC:
Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Sparcraft Bayonet Pin & Toggle Assembly. Sparcraft Bayonet Pin (7/8" OD x 4" long, beneath head) fits all Sparcraft Bayonet type Spinnaker Pole ends, See Spinnaker Poles & Parts. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Toggle projects 4" (maximum) from Track surface. Har 783 Cars use (72) 3/8" Torlon Balls.
	Car only for Harken Big Boat Track & Sparcraft Pin: Har 783: Spinnaker Car only to fit Harken Big Boat Track and Sparcraft Bayonet Pin & Toggle Assembly. Extruded Aluminum Car includes 5/8" vertical Pin with 1 3/16" clearance for Sparcraft Bayonet Pin & Toggle Assembly. Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Pin center is 1 7/16" from Track surface. Har 783 Cars use (72) 3/8" Torlon Balls. *As Har 783-SC,* above, but without Sparcraft Bayonet Pin & Toggle Assembly.
	Sparcraft Pin & Toggle Ass'y - 5/8" Pin: SPC 73-13PT-1: Replacement Sparcraft Bayonet Pin & Toggle (Type 1) Assembly fits all Sparcraft Bayonet type Spinnaker Pole ends, and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Assembly includes Sparcraft Bayonet Pin, SPC 73-13P, and SS Toggle SPC 73-12T1.
	*Sparcraft Bayonet Pin only: SPC 73-13P:* Replacement Sparcraft Bayonet Pin only, fits all Sparcraft Bayonet type Spinnaker Pole ends. Stainless Steel Sparcraft Bayonet Pin is 7/8" OD x 4" long (beneath head), head is 9/16" thick with hole for 1/2" pin. Unit is (maximum) 5 3/4" long.
	*Sparcraft Type 1 Toggle only: SPC 73-12T1:* Replacement Sparcraft Toggle (Type 1) fits Sparcraft Bayonet Pin and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Stainless Steel Toggle is 1 3/16" high x 1 3/8" wide with holes for 5/8" (Vertical) and 1/2" (Horizontal) Pins, and measures 1 5/8" between Pin centers. Horizontal (1/2") Pin is included.

Spinnaker Car w/ Small Bell for Harken Big Boat Track: Har 782-MBS:
Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Metric Small Bell Fitting (B-130). Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD. Metric Small Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end, See Metric Spinnaker Poles & Parts. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide. Har 782 Cars use (72) 3/8" Torlon Balls.
Spinnaker Car w/ Large Bell for Harken Big Boat Track: Har 782-MBL:
Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Metric Large Bell Fitting (B-120). Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD. Metric Large Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 70, 80 and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end, See Metric Spinnaker Poles & Parts. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide. Har 782 Cars use (72) 3/8" Torlon Balls.
	Car only for Harken Big Boat Track & Bell Fitting: Har 782: Spinnaker Car only to fit Harken Big Boat Track and Harken/ Barbarossa Metric Bell Fittings. Extruded Aluminum Car includes 12mm vertical Pin with clearance for Harken/ Barbarossa Metric Bell Fittings, B-120, and B-130. Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Pin center is 1 1/2" from Track surface. Har 782 Cars use (72) 3/8" Torlon Balls. As Har 782-MBS, and Har 782-MBL, above, but without Bell Fitting and Toggle. PC
	*Metric Small Bell & Toggle only: Har B-130:* Replacement Metric Small Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa/ Harken inboard Small Bell Pole Ends. Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm Pin and is 1 3/8" (34mm) high. Metric Small Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. See Metric Spinnaker Poles & Parts. For Small Bell and Toggle Components, See Replacement Metric Bell Fittings.
	*Metric Large Bell & Toggle only: Har B-120:* Replacement Metric Large Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa/ Harken inboard Large Bell Pole Ends. Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD, Toggle has hole for 12mm Pin and is 1 3/8" (34mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on Poles of 70, 80, and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. See Metric Spinnaker Poles & Parts.

Spinnaker Cars for NF 1100 RCB Track
Spinnaker Ring Car for NF 1100 RCB Track: NF 1182: Recirculating Ball Spinnaker Car to fit NF 1100 RCB Track. Car has large SS Ring assembly screwed to extruded Aluminum Body. Car is 4 9/16" long x 2 3/8" wide, SS Ring is 7/16" x 1 3/4" ID, and projects 3 1/8" (maximum) from Track surface. NF 1182 Car uses (60) 1/4" Torlon Balls. Nicro-Fico NF 1100 Recirculating Ball (RCB) Track measures 15/16" (24mm) across the top.

Your cart

Spars, Rigging, and Hardware for Sailboats