Z-Spar Spreader Z-240

Z-Spar Z240 Spreader Section Outside Measurements (Untapered): 130mm x 40mm (5 1/8" x 1 9/16") Inside Measurements: 86mm x 32mm (3 3/8" x 1 1/4") Wall thickness: 3mm Weight/M.: 2.4kg. - Weight/ft.: 1.61 lbs.
The Z240 Spreader Section features an integral "tail", so that the Spreaders (as an option) can be tapered at the outboard end without welding. Z240 Spreader Assemblies are available in Standard (untapered), and Tapered versions with a variety of inboard and outboard end fittings, listed below.

*Z240 Standard Untapered Spreader Assembly: Z-240AS-__:* *Z240 Standard Untapered Spreader Ass'y - Angled Aft: Z-240ASA-__:* Standard Untapered Z240 Spreader Assembly is clear anodized and includes Z-3115L Spreader Tip. To order specify maximum tube length, and sweepback angle (if any). If any inboard end is required, specify Part Number.
Z240 Standard Untapered Spreader Tube only to 3': Z-240T-1xx: Z240 Standard Untapered Spreader Tube only to 6': Z-240T-2xx: Z240 Standard Untapered Spreader Tube only - Angled Aft: Z-240TAA-xxx: Standard Untapered Z240 Spreader Tube is clear anodized. To order specify maximum tube length, and sweepback angle (if any).
Z240 Tapered Spreader Assembly: Z-240AT-____: *Z240 Tapered Spreader Ass'y - Angled Aft: Z-240ATAA-__:* Tapered Z240 Spreader Assembly is clear anodized and includes Z-3115C Spreader Tip. To order specify maximum tube length, up to 1.8M (72") and sweepback angle (if any). If other Tip or any inboard end is required, specify Part Number(s).
Z240 Tapered Spreader - Tube only, Tapered & Drilled: Z-240TT-____: Z240 Tapered Spreader Tube only - Angled Aft: Z-240TTAA-xxx: For replacement purposes when using original end fittings, Z240 Spreader Tubes are available Tapered and drilled for *Z-3115* Spreader Tip, and with inboard angles cut. To order specify maximum tube length, and sweepback angle (if any). Clear anodized finish is standard. Painted finishes are available on special order, specify color.
Z240 Spreader Section, Clear Anodized: Z-240CA-____: Z240 Spreader Section is available clear anodized, but without taper or drilling at lengths up to 20'. To order specify maximum length.

Spreader Tips & Components for Z240 Spreaders
L-Bolt Tips require that the Tip be removed from the Spreader to adjust Clamp tension.
*Spreader Tip Ass'y for Z240 Tapered Spreader: Z-3115:* Gray plastic Spreader Tip for use with Tapered Z240 Spreader. Includes 6mm L-bolt with locknut, Z-1479A, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 4" x 1 13/16" wide (112mm x 46mm). This item is no longer available, having been replaced by the Z-3115C, below.
*Spreader Tip Ass'y for Z240 Standard Spreader: Z-3115L:* Gray plastic Spreader Tip for use with Standard Untapered Z240 Spreader. Includes 6mm L-bolt with locknut, Z-1479A, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 5 3/8" long x 1 13/16" wide (137mm x 46mm).
		L-bolt w/ Locknut for Z240 Spreader Tip: Z-1479A: SS L-bolt is 2" (50mm) long with a 6mm thread and includes SS locknut. For use with *Z-3115* and *Z-3115L* Spreader Tips.
C-Clamp type Tips allow adjustment of Clamp tension without removing the Tip from the Spreader.
*Spreader Tip Ass'y for Z240 Tapered Spreader: Z-3115C:* Gray plastic Spreader Tip for use with Tapered Z240 Spreader. Includes C-Clamp with screw, Z-1479CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 4" x 1 13/16" wide (112mm x 46mm).
*Spreader Tip Ass'y for Z240 Standard Spreader: Z-3115LC:* Gray plastic Spreader Tip for use with Standard Untapered Z240 Spreader. Includes C-Clamp with screw, Z-1479CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 5 3/8" long x 1 13/16" wide (137mm x 46mm).
		C-Clamp w/ Screw for Z240 Spreader Tip: Z-1479CA: SS C-Clamp with 6mm socket head screw is used to clamp shroud to the spreader tip. For use with *Z-3115C* and *Z-3115LC* Spreader Tips. Cast Clamp is marked 4235.
Heavy Duty Tips
*Spreader Tip Ass'y for Z240 Spreader - Triple Shroud: Z-3109:* Cast aluminum Spreader Tip for use with Tapered Z240 Spreader incorporates provisions for up to 3 shrouds (the largest up to 12mm (7/16")). Shrouds are captured by smooth outer casting that is attached to the base casting with one screw. Recessed Allen head cap screw (6mm) threads into captive locknut in base casting.

Discontinuous Tips
Discontinuous Spreader Tip for Z240 Spreader - 12mm: Z-181-12:
Special cast aluminum Spreader Tip for use with Tapered Z240 Spreader incorporates a wide slot for a 12mm Pin used with Dermac Hinged Tip Cup Assembly. Unit projects (maximum) 1 5/8" (42mm) from end of spreader tube and is (maximum) 3 3/4" (95mm) wide. Slot width is 1 3/4" (44mm), pin center is 1" (25mm) from tube end. A single 12mm pin, Z-1155P-12, is included. Limited availability.
HD Discontinuous Spreader Tip for Z240 - 14/10mm: Z-181-1410:
Heavy duty cast aluminum Spreader Tip for use with Tapered Z240 Spreader is threaded to accept a 14mm bolt for the main shrouds and incorporates a 10mm inboard pin for intermediate shrouds. Compact design requires spreader tube to be notched to accommodate intermediate shrouds. Design allows for Discontinuous or Continuous Diagonal shrouds. Bolt and pin are included. Limited availability.
Discontinuous Tip for Z240 – 12mm/10mm Pins: Z-1155-1210: Discontinuous Tip for Z240 – 14mm/10mm Pins: Z-1155-1410: Discontinuous Tip for Z240 – 16mm/10mm Pins: Z-1155-1610: Discontinuous Tip for Z240 – 14mm/12mm Pins: Z-1155-1412: Discontinuous Tip for Z240 – 16mm/12mm Pins: Z-1155-1612: Cast aluminum Spreader Tip for use with Tapered Z240 Spreader incorporates a 12, 14, or 16mm Pin outboard for the main shrouds, and a 10 or 12mm inboard Pin for intermediate shrouds. Design allows for Discontinuous or Continuous Diagonal shrouds. Unit projects (maximum) 3 15/16" (100mm) from end of spreader tube. Slot width (at outboard pin) is 1 5/8" (40mm), pin center is 2 1/2" (62mm) from tube end. Inboard Pin has slot width of 1/2" (12mm), small pin center is 1" (25mm) from tube end. Pins are included.
	10mm pin for Z-1155 Tip Casting: Z-1155P-10: 12mm pin for Z-1155 Tip Casting: Z-1155P-12: 14mm pin for Z-1155 Tip Casting: Z-1155P-14: 16mm pin for Z-1155 Tip Casting: Z-1155P-16: 19mm pin for Z-1155 Tip Casting: Z-1155P-19: SS Pins only for rigging attachment on Z-1155 Discontinuous Spreader Tips, above. 10 and 12mm Pins are 72mm (2 7/8") long, 14, 16 and 19mm Pins are 87mm (3 7/16") long.
Discontinuous Spreader Tip for Z240 'Untapered' 16mm/10mm: Z-1155NT-1610:
Discontinuous Spreader Tip for Z240 'Untapered' 16mm/12mm: Z-1155NT-1612:
Discontinuous Spreader Tip for Z240 'Untapered' 19mm/12mm: Z-1155NT-1912:
Cast aluminum Spreader Tip for use with Standard Z240 Spreader incorporates a 16mm or 19mm Pin outboard for the main shrouds, and a 12mm inboard Pin for intermediate shrouds. Design allows for Discontinuous or Continuous Diagonal shrouds. Unit projects (maximum) 3 15/16" (100mm) from end of spreader tube. Slot width (at outboard pin) is 1 5/8" (40mm), pin center is 2 1/2" (62mm) from tube end. Inboard Pin has slot width of 1/2" (12mm), small pin center is 1" (25mm) from tube end. Pins (included) are as Z-1155P, above.

Inboard Spreader Ends & Spreader Bases for Z240 Spreaders
Inboard Hinge End for Z240 Spreader – (-5)° aft: Z-1220-(-5):
*Inboard Hinge End for Z240 Spreader – 0° aft: Z-1221-0:* Inboard Hinge End for Z240 Spreader – 8° aft: Z-1222-8: Inboard Hinge End for Z240 Spreader – 15° aft: Z-1224-15: Inboard Hinge End for Z240 Spreader – 20° aft: Z-1225-20: Inboard Hinge End for Z240 Spreader – 28° aft: Z-1223-28: Inboard Hinge End for Z240 Spreader – 32° aft: Z-1226-32: Special Inboard Hinge End with Tangs is used to attach Z240 Spreader to hinged spreader base using 12mm SS Pin, Z-1317X (available separately). Unique design incorporates double lower Stemball tangs as part of the inboard spreader end. Units are available with a variety of standard angles built in for swept back spreaders. Cast aluminum unit is 4" wide x 1 3/16" thick at Pin hole. SS 12mm Hinge Pin is not included, See Z-1317X, below. Note: While most of these units have a part number and a ° marking cast into the part, these numbers are frequently incorrect. It is strongly recommended that you measure the angle with a protractor and NOT go by these markings. Items listed as "Out" have been discontinued by the Factory and are no longer available.

Hinged Spreader Base for Z240 Spreaders - Small, Port: Z-1038P: *Hinged Spreader Base for Z240 Spreaders - Small, Starboard: Z-1037S:*
Hinged Spreader Base assembly for Z240 Spreaders is used on Z600, Z601, Z700, Z701, Z800, Z900, & Z901 Mast sections. Base measures (max.) 7" wide (178mm) x 5 1/8" (130mm) high. SS 12mm Hinge Pin is not included, See Z-1317X, below.
Hinged Spreader Base for Z240 Spreaders - Large, Port: Z-1045P: Hinged Spreader Base for Z240 Spreaders - Large, Starboard: Z-1044S:
Hinged Spreader Base assembly for Z240 Spreaders is used on Z1001 and Z1100 Mast sections. Base measures (max.) 7" wide (178mm) x 5 1/8" (130mm) high. SS 12mm Hinge Pin is not included, See Z-1317X, below.
		Hinge Pin for Z240 Spreader Base: Z-1317X: SS Pin is held in place with a single cotter pin secured through the base. Pin measures 12mm x 145mm (5 3/4") long. For use with all Z240 Spreaders Bases above.


Spreader Bars for Z240 Spreaders
Aluminum Spreader Bars for Z240 Spreaders Extruded Aluminum Spreader Bars for Z240 Spreaders feature a slot for a SS Fixing Plate to secure the Spreaders in place.
Aluminum Spreader Bar for Z240 - 0° aft: Z-5040-0: Aluminum Spreader Bar for Z240 - 10° aft: Z-5041-10: Aluminum Spreader Bar for Z240 - 15° aft: Z-5042-15: Aluminum Spreader Bar for Z240 - 20° aft: Z-5043-20: Aluminum Spreader Bar for Z240 - 25° aft: Z-5044-25: Aluminum Spreader Bar for Z240 - 30° aft: Z-5045-30: Extruded Aluminum Spreader Bar for Z240 Spreaders is 31mm thick x 50mm wide (1 1/4" x 2") with a 21mm wide slot, and is available in a variety of angles. Used with a variety of Aluminum Reinforcing Plates. When ordering please specify Mast Section and spreader angle (if any).
Fixing Plate for Z240 Alu. Spreader Bar - 25mm: Z-4905AX:
SS Fixing Plate for Z240 Old-style Aluminum Spreader Bar with 26mm (1") wide slot. SS Plate is 25mm wide x 5mm thick x 90mm long (1" x 3/16" x 3 1/2") with (2) 5mm holes on 48mm centers, (1) hole is tapped. Includes (1) 5mm x 16mm screw.
Fixing Plate for Z240 Alu. Spreader Bar - 20mm: Z-4714A:
SS Fixing Plate for Z240 Aluminum Spreader Bar with 21mm (13/16") wide slot. SS Plate is 20mm wide x 5mm thick x 100mm long (3/4" x 3/16" x 4") with (2) 8mm holes on 70mm centers, (1) hole is tapped. Includes (1) 8mm x 16mm screw.

Reinforcing Plate for Z240 Spreader Bar Z601+, 0-15°: Z-4911: Reinforcing Plate for Z240 Spreader Bar Z601+, 20°+: Z-4912:
Aluminum Plate is formed to fit the mast section and features boss to allow a straight cut on the spreader end. Plate is 7 1/4" long x 3 1/4" (maximum) wide (185 x 84mm), slot in plate is 1 1/4" (32mm) high. Plates (2 required) are attached to the mast with (6) 1/4" (6mm) rivets. For use with Z601 - Z901 & Z600E - Z902E Mast Sections. Use Z-4911 (2" (52mm) long slot) for Bars up to 15° aft. Use Z-4912 (2 1/4" (58mm) long slot) for Bars from 20° to 30° aft.
Reinforcing Plate for Z240 Spreader Bar Z1001, 0-15°: Z-4913: Reinforcing Plate for Z240 Spreader Bar Z1001, 20°+: Z-4914:
Aluminum Plate is formed to fit the mast section and features boss to allow a straight cut on the spreader end. Plate is 7 1/4" long x 3 1/4" (maximum) wide (185 x 84mm), slot in plate is 1 1/4" (32mm) high. Plates (2 required) are attached to the mast with (6) 1/4" (6mm) rivets. For use with Z1001 & Z1100E Mast Sections. Use Z-4913 (2" (52mm) long slot) for Bars up to 15° aft. Use Z-4914 (2 1/4" (58mm) long slot) for Bars from 20° to 30° aft.

Your cart

Spars, Rigging, and Hardware for Sailboats