 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
ISOMAT ISOFURL |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
ISOMAT ISOFURL |
|
|
|
|
|
Isofurl # 8 Rod Measurements: 17.55mm (11/16") fore & aft x 20.5mm (13/16") Equivalent Wire Size: 7mm (9/32") Luff Tape: #6 (3/16") Isofurl # 10 Sailmakers, See Isofurl Sailmaker Instructions
|
Isofurl
|
|
The Isofurl is a solid-rod type Jib furling system, with Twin Luff Grooves. This system replaces the Headstay and has no stay inside the furling Rod. Produced by Isomat, the French Sparbuilder, it was assembled full length and shipped with the mast as part of a 'package' sold to many Boatbuilders, production of this System was discontinued in 1995. The solid rod Isofurl system came in 2 different Rod sizes. To determine which size you have, you will have to measure the Rod. Most Isofurl systems came with a "Halyard Hoist Locking Car", to which the head of the
sail was attached. This car is hoisted by a special hook (Isofurl 810-H)
with a long messenger line attached to it. The halyard is attached to the top of the hook NOT
to the locking car. When the car is hoisted to the top of the system, it locks in place,
and the halyard (with hook still attached) is pulled down with a messenger line. Some Isofurl systems came with a conventional-type Halyard Swivel, to which the halyard stayed attached after hoisting. This Halyard Swivel was also used as a retrofit by those who preferred the more conventional arrangement. In rare cases where the 'locking lip' at the top of the system has worn, or broken off, the halyard locking car will no longer lock. The Halyard Swivel is an effective cure for this problem as well, and installs easily in minutes. For System Details, See: Isofurl System Diagrams |
|
|
|
|
| COMMON ISOFURL PARTS | ||
Most parts are still available for Isofurl Systems.
|
||
|
Upper Bearing Assembly w/ Eye This unit threads directly onto the Upper Rod End and contains the Bearings that allow the rod to rotate, as well as an Eye that connects the system to the Forestay Toggle. Forestay Toggles are required for use with all Furling Systems. When reattaching the Upper Bearing Assembly to the Rod End new Teflon thread tape (a standard plumbing item) should be used on the screw threads to help prevent water intrusion. Length (L) is the length of the Assembly from the bottom of the unit to the center of the clevis Pin hole. |
|
|
|
Isofurl Upper Bearing & Eye Ass'y for 10mm Pin, L=5": Isofurl UBE-10S:
Isofurl Upper Bearing & Eye Ass'y for 10mm Pin, L=6.5": Isofurl UBE-10L: Isofurl Upper Bearing & Eye Ass'y for 12mm Pin, L=5.1": Isofurl UBE-12S: Isofurl Upper Bearing & Eye Ass'y for 12mm Pin, L=6.5": Isofurl UBE-12L: Isofurl Upper Bearing & Eye Ass'y for 14mm Pin, L=5.4": Isofurl UBE-14S: Isofurl Upper Bearing & Eye Ass'y for 14mm Pin, L=5.7": Isofurl UBE-14SH: Isofurl Upper Bearing & Eye Ass'y for 14mm Pin, L=6.8": Isofurl UBE-14L: Isofurl Upper Bearing & Eye Ass'y for 16mm (5/8") Pin, L=5.5": Isofurl UBE-16S: Isofurl Upper Bearing & Eye Ass'y for 16mm (5/8") Pin, L=6": Isofurl UBE-16SH: Isofurl Upper Bearing & Eye Ass'y for 16mm (5/8") Pin, L=7": Isofurl UBE-16L:
|
||
| Bearing Replacement Kits Isofurl systems have a set of 3 highly specialized torque bearings with special SS spacers and seals in an aluminum housing on each end of the rod. Long term study has indicated, that often, even after 30 years, only One End requires Bearing Replacement, the other lasting indefinitely. As a result, Bearing Replacement Kits are now offered individually. Bearing Replacement Kits contain all the bearings and seals necessary to rebuild either end of the System. Special tools are required, as bearings are press-fit. However, if your Bearings require replacement and other items are worn, we recommend that you Replace the Upper and/or Lower Ends (Upper Bearing Ass'y, above, and Lower Bearing Ass'y, below). See: Isofurl Bearing Replacement. Isofurl #8/10 Bearing Replacement Kit - One End: Isofurl 810-BK-1: Isofurl #8/10 Bearing Replacement Kit - Both Ends: Isofurl 810-BK-2: Bearing Replacement Kits contain all the bearings and seals necessary to rebuild One or Both System ends (Special SS Bearing Spacers last indefinitely, your existing ones are reused). Kits include all components necessary to replace Bearings and Seals in either End of the System. **Bearing Replacement Kits are recommended for use by Professionals only, Special tools are required, as bearings are press-fit. If this service is not available locally, we will install them for a small additional charge - send us one or both aluminum housings as unscrewed directly from the rod ends. See: Isofurl Bearing Replacement.
|
||
|
Halyard Hoist Locking Car Assembly Isofurl #8 Halyard Hoist Locking Car: Isofurl 8-HLC: Isofurl #8 Heavy-duty Halyard Locking Car: Isofurl 8-HLC-H: Isofurl #10 Halyard Hoist Locking Car: Isofurl 10-HLC: Isofurl #10 Heavy-duty Locking Car: Isofurl 10-HLC-H: Available in two sizes to fit the two different size Rods. A Heavy-duty version is available with contoured SS straps between the pivot pin and the Head shackle, Heavy-duty shackle is included. Halyard Hoist Hook Isofurl 810-H (available separately), is used to hoist the Locking Car.
|
|
|
|
Halyard Hoist Hook Isofurl Halyard Hoist Hook: Isofurl 810-H: Special SS Hook is used to hoist the Locking Car. For use with all Isofurl Systems using a Halyard Hoist Locking Car.
|
|
|
Halyard Swivel Isofurl #8 Halyard Swivel: Isofurl 8-HS: - NLA Isofurl #10 Halyard Swivel: Isofurl 10-HS: Though not commonly supplied with most Isofurl systems, a conventional-type Halyard Swivel is sometimes used to replace the Halyard Hoist Locking Car. When using a Halyard Swivel, the halyard stays attached after hoisting the sail, as in conventional furling systems. Available in two sizes to fit the two different size Rods.
|
||
|
Sail Feeder Isofurl #8 SS Sail Feeder: Isofurl 8-F: Isofurl #10 SS Sail Feeder: Isofurl 10-F: Stainless Steel Sail Feeder fits into notches milled into the Rod and is glued in place. Available in two sizes to fit the two different size Rods.
|
||
|
Drum Assembly Two-piece drum assemblies (and drum halves) are available in 3 different diameters. All sizes fit all Isofurl Systems, but only work with one size Stainless Steel Lineguard. If you are changing Drum sizes, you will also need to change Lineguards. Drums are listed by Maximum diameter. To order a replacement Drum, you must know your existing Drums' largest diameter. The Aluminum Drum Assembly, Isofurl DA-3A, includes two-piece cast internal shim.
|
||
|
Internal Shim for Isofurl Aluminum Drum: Isofurl DA-3S: The Isofurl Aluminum Drum requires the use of (2) internal shims to attach it to the Lower Rod End housing. Two (2) pieces are included with the Aluminum Drum Assembly, but Shims are also available separately. Cast Aluminum Shim (sold each) is 2 7/8" wide x 3 1/8" high.
|
||
|
Stainless Steel Lineguard Assembly Isofurl SS Lineguard for 6 1/4" (160mm) Diameter Drum: Isofurl LG-1: Isofurl SS Lineguard for 6 13/16" (175mm) Diameter Drum: Isofurl LG-2: Isofurl SS Lineguard for 9 3/8" (238mm) Diameter Drum: Isofurl LG-3: Lineguards are available for 3 different drum diameters. All sizes fit all Isofurl Systems, but only work with one size Drum Assembly. Drums are listed by Maximum diameter. To order a replacement Lineguard, you must know your existing Drum diameter.
|
||
|
Lower Assembly Complete w/ Adjusting Screw & Toggle A Complete Lower End Assembly that threads directly onto the Lower Rod End includes: a Lower Bearing Assembly, Isofurl 810-LBA, an Adjustment Screw Socket, and an Adjusting Screw with Toggle. Order components separately, as required, below.
|
|
|
|
Lower Bearing Assembly Isofurl #8/10 Lower Bearing Assembly: Isofurl 810-LBA: Lower Bearing Assembly contains the Bearings that allow the rod to rotate, as well as the toggling assembly that the lineguard clamps to. It threads directly onto the Lower Rod End and onto the Adjustment Screw Socket for the Adjusting Screw with Toggle that attaches to the deck. Unit is 5 1/16" (130mm) long. When reattaching the Lower Bearing Assembly to the Rod End or the Adjustment Screw Socket, new Teflon thread tape (a standard plumbing item) should be used on the screw threads to help prevent water intrusion.
|
||
| Adjustment Screw Socket Adjustment Screw Socket threads directly onto the Lower (bearing end) End of the Lower Bearing Assembly. The Adjusting Screw with Toggle threads into it. When reattaching the Adjustment Screw Socket to the Lower Bearing Assembly, new Teflon thread tape (a standard plumbing item) should be used on the screw threads to help prevent water intrusion.
Isofurl Adjustment Screw Socket - 10mm: Isofurl LSS-10-___:
|
||
| Adjusting Screw w/ Toggle Available in a number of configurations and sizes with an integral toggle, or as an eye with a removable toggle. Measure thread size and threaded length to determine which item you require, Thread and Pin size are the same. Set screws (2 sizes) are included.
These sizes have been produced in other lengths, contact us if yours is not listed. |
|
|
~ Back to Furling Systems Main Page ~
~ Home ~