 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
NB-32 Gooseneck Assemblies & Parts |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
NB-32 Gooseneck Assemblies & Parts |
|
|
|
|
|
Isomat NB-32 Boom Section Outside Measurements (Maximum): 5" x 4 3/8" (128mm x 110mm) Wall Thickness: .085" Weight/ft.: 2.16 lbs. New-Style Goosenecks are listed below, Old-Style Goosenecks are listed separately, See: Old-Style NB-32 Gooseneck Assemblies and Parts. Note that some Booms have been produced with the Isomat AutoReef (single line) Reefing System, using specially modified Boom End castings and additional components. For details, See: Isomat AutoReef System. |
||
|
|
||
|
NG2 Gooseneck Bracket: NG2-11:
Cast aluminum Gooseneck Mast Bracket for use with NB-32, NB-40, and NB-55 new-style Gooseneck Assemblies. Bracket for NG-51 through NG-86 Mast Sections is 4 3/4" (120mm) high x 3 1/2" (90mm) wide, and is fastened with eight (8) 1/4" (6mm) rivets. Bracket has 22mm (7/8") hole at top and 8mm (5/16") hole on bottom side, for use with any of the NB2-1 Vertical Gooseneck Toggle Pins. Though actually a Mast Component, this item is also listed here for your convenience.
|
|
|
|
NB-32 Gooseneck Assembly Complete: NB32-1AC: Cast aluminum Gooseneck Assembly incorporates provisions for internal outhaul and 3 internal reef lines. Internal lines run over delrin sheaves, and down past lever action cams. Cams can be removed to allow lines to go straight down to the deck. Includes Vertical Gooseneck Toggle Pin with reef hooks, and tack shackle. For use with Isomat Gooseneck Mast Bracket (NG2-11), which has 7/8" hole at top and 5/16" hole on bottom side.
|
|
|
|
NB-32 Gooseneck Assembly: NB32-1A: As NB32-1AC, above, but with sheaves, cams, and axles only. Does not include Vertical Gooseneck Toggle Pin with reef hooks, and tack shackle.
|
|
|
|
NB-32 Gooseneck Casting: NB32-1: Replacement Casting only, for any of the NB-32 Gooseneck Assemblies listed above.
|
||
|
NB2 Gooseneck Toggle Ass'y w/ Reef Hooks: NB2-1A:
Vertical Gooseneck Toggle Pin Assembly with Tack Shackle and Reef Hooks is used to attach the NB32-1 Gooseneck to Isomat Gooseneck Mast Bracket (NG2-11). SS Toggle Pin has 2 integral Reef Hooks and is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, with washer and SS Locknut. Assembly includes Tack Shackle (NB2-2) and Horizontal Gooseneck Pin (NB2-3).
|
|
|
|
NB2 Gooseneck Toggle Pin w/ Reef Hooks: NB2-1:
Vertical Gooseneck Toggle Pin with Reef Hooks includes washer and SS Locknut. As NB2-1A, above, but without Tack Shackle and Horizontal Gooseneck Pin. SS Toggle Pin has 2 integral Reef Hooks and is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, and has (2) 10mm (3/8") cross-holes for Tack Shackle and Horizontal Gooseneck Pin.
|
||
|
NB2 Tack Shackle: NB2-2:
SS Tack Shackle fits through hole in top of NB2 Vertical Gooseneck Toggle Pins. Shackle has 8mm (5/16") pin, throat width is 22mm (7/8").
|
|
|
|
Screw Pin for NB2-2 Tack Shackle: NB2-2SP:
Replacement Screw Pin only for NB2-2 Tack Shackle. Screw Pin has 8mm thread.
|
||
| NB2 Horizontal Gooseneck Pin: NB2-3:
Clevis Pin is 10mm (3/8") dia. x 49mm (2") long. Used to attach the NB32-1 Gooseneck to Isomat Vertical Gooseneck Toggle Pin, NB2-1.
|
||
|
NB2 Vertical Gooseneck Toggle Ass'y: NB2-1ARA:
Vertical Gooseneck Toggle Pin Assembly is used to attach the NB32-1 Gooseneck to Isomat Gooseneck Mast Bracket (NG2-11). For use with AutoReef Systems not requiring Reef hooks. SS Toggle Pin is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, with washer and SS Locknut. Assembly includes Tack Shackle (NB2-2) and Horizontal Gooseneck Pin (NB2-3).
|
|
|
|
NB2 Vertical Gooseneck Toggle Pin - AR: NB2-1AR:
Vertical Gooseneck Toggle Pin includes washer and SS Locknut. As NB2-1ARA, above, but without Tack Shackle and Horizontal Gooseneck Pin. For use with AutoReef Systems not requiring Reef hooks. SS Toggle Pin is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, and has (2) 10mm (3/8") cross-holes for Tack Shackle and Horizontal Gooseneck Pin.
|
||
|
NB-32 Early Vertical Gooseneck Toggle Pin: NB2-1XP: Early version Vertical Gooseneck Toggle Pin Assembly is used to attach the NB32-1 Gooseneck to Isomat Gooseneck Mast Bracket (NG2-11). Has 10mm (3/8") cross pin at top for using the Old-Style Reef Hook/Tack Assembly (NB2-5X). SS Toggle Pin is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, has 10mm (3/8") cross-hole for Horizontal Gooseneck Pin (NB2-3), and includes washer and SS Locknut.
|
||
|
NB2 Early Reef Hook/Tack Attachment: NB2-5X:
Early version formed combination SS Reef Hook and Tack anchor is passed through the tack grommet in sail and clipped over horizontal cross pin in top of special 22mm gooseneck pin, NB2-1XP. Formed from heavy 10mm (3/8") SS rod, unit measures a maximum of 4" (100mm) high x 3 1/2" (90mm) wide.
|
|
|
|
NB2 Boom Sheave: NG1-4:
Acetyl Sheave is 60mm (2 5/16") OD x 14mm (9/16") wide x 10mm (3/8") ID, and fits in upper (aft) slot in Gooseneck Casting.
|
|
|
|
NB2 Boom Sheave - Aluminum: NG1-4A:
Anodized Aluminum Sheave is 60mm (2 5/16") OD x 14mm (9/16") wide x 10mm (3/8") ID, and is much sturdier than the plastic version.
|
||
|
Sheave Axle for NB-32 Gooseneck: NB2-12:
SS 'Drop-in' Sheave Axle pin is 10mm (3/8") dia. x 81mm (3 3/16") long, and fits in upper (aft) slot in NB32-1 Gooseneck Casting.
|
 |
|
|
Cam Axle for NB-32 Gooseneck: NB2-13:
SS 'Drop-in' Cam Axle pin is 10mm (3/8") dia. x 79mm (3 1/8") long, and fits in lower (forward) slot in NB32-1 Gooseneck Casting.
|
|
|
|
AutoReef Roller Axle for NB-32 Gooseneck: NB2-12X:
SS knurled Axle pin is 10mm (3/8") dia. x 90mm (3 9/16") long. Used as axle for AutoReef Roller sheaves.
|
|
|
|
AutoReef Roller for NB-32 Gooseneck: NB1-20R:
Delrin Roller sheave is 22mm (7/8") OD x 14mm (9/16") wide x 10mm (3/8") ID. Used with knurled axle in NB-32 AutoReef Gooseneck.
|
||
|
AutoReef Roller for NB-32 Gooseneck: NB2-20R: Delrin Roller sheave is 35mm (1 3/8") OD x 15mm (9/16") wide x 10mm (3/8") ID. Used with knurled axle in NB-32 AutoReef Gooseneck.
|
||
|
Gooseneck Cam - New Style: NBA-14:
New-Style Gooseneck Cam lever used in all New-Style NB boom goosenecks. Anodized extruded aluminum cam measures (max.) 2 3/4" long x 9/16" wide (70 x 14mm), and rides on 10mm (3/8") cam axle.
|
|
|
~ Home ~
