 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
NB-32 Old-Style Gooseneck Assemblies & Parts |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
NB-32 Old-Style Gooseneck Assemblies & Parts |
|
|
|
|
|
Isomat NB-32 Boom Section Outside Measurements (Maximum): 5" x 4 3/8" (128mm x 110mm) Wall Thickness: .085" Weight/ft.: 2.16 lbs. Old-Style Goosenecks are listed below, New-Style Goosenecks are listed separately, See: New-Style NB-32 Gooseneck Assemblies and Parts. |
||
|
|
||
|
NG2 Old-Style Gooseneck Bracket: NG2-11X:
Cast aluminum Gooseneck Mast Bracket for use with NB-32, NB-40, and NB-55 old-style Gooseneck Assemblies. Bracket for NG-51 through NG-86 Mast Sections is 3 7/8" (98mm) high x 3 1/2" (90mm) wide, and is fastened with eight (8) 1/4" (6mm) rivets. Bracket has hole for 10mm (3/8") Vertical Pin, NB2-1XA, used with SS Gooseneck Toggle NB2-2XA. This item is no longer available, having been replaced by the stronger SS version, NG2-11X-SS, below.
|
 |
|
|
NG2 Old-Style Gooseneck Bracket: NG2-11X-SS:
SS Replacement for Cast aluminum NG2-11X used with NB-32, NB-40, and NB-55 old-style Gooseneck Assemblies. Welded SS Bracket for NG-51 through NG-86 Mast Sections is 3 7/8" (98mm) high x 3 1/2" (90mm) wide, and is fastened with eight (8) 1/4" (6mm) rivets. Bracket has hole for 10mm (3/8") Vertical Pin, NB2-1XA, used with SS Gooseneck Toggle NB2-2XA.
|
||
|
NB-32 Old-Style Gooseneck Assembly Complete: NB32-1XAC:
Cast aluminum Gooseneck Assembly incorporates provisions for internal outhaul and 3 internal reef lines. Internal lines run over delrin sheaves, and down past lever action cams. Cams can be removed to allow lines to go straight down to the deck. Includes Gooseneck Toggle with reef hooks, tack pin, and Vertical Gooseneck Pin. For use with SS Isomat Gooseneck Mast Bracket for 10mm (3/8") vertical pin.
|
||
|
NB-32 Old-Style Gooseneck Assembly: NB32-1XA:
As NB32-1XAC, above, but with sheaves, cams, and axles only. Does not include Gooseneck Toggle with reef hooks, tack pin, and Vertical Gooseneck Pin.
|
|
|
|
NB-32 Old-Style Gooseneck Casting: NB32-1X:
Replacement Casting only, for any of the NB-32 Gooseneck Assemblies listed above.
|
||
| NB2 Old-Style Gooseneck Toggle w/ Tack, Reef Hooks & Vertical Bolt: NB2-2XAC: | ||
| Heavy SS Toggle Assembly features 10mm
(3/8") Tack Pin and 2 Reef Hooks. Assembly is 5 5/8" high x 3 3/8" long,
and accepts a 7/8" wide gooseneck nose. Used to attach the Old-Style NB-32 Gooseneck
to Isomat Gooseneck Mast Bracket for 10mm (3/8") vertical pin. Lower section of
assembly (that goes between Mast Bracket tabs) is 2 1/8" (55mm) high. Includes
Vertical Gooseneck Bolt and Locknut (NB2-1XA), Tack Pin (NB2-2XP),
and Horizontal Gooseneck Bolt with SS Locknut (NB2-3XA).
012
|
 |
|
|
NB2 Old-Style Toggle w/ Tack & Reef Hooks: NB2-2XA:
Heavy SS Toggle Assembly as NB2-2XAC, above, but without Vertical Gooseneck bolt NB2-1XA. Includes Tack Pin (NB2-2XP) and Horizontal Gooseneck Bolt with SS Locknut (NB2-3XA).
|
||
|
NB2 Old-Style Vertical Gooseneck Bolt: NB2-1XA:
Special machined bolt is 10mm (3/8") dia. x 125mm (4 7/8") long. Used to attach the Old-Style Gooseneck Toggle with Tack and Reef Hooks (NB2-2XA) to Isomat Gooseneck Mast Bracket for 10mm (3/8") vertical pin. Includes 10mm SS locknut.
|
||
|
NB2 Old-Style Gooseneck Tack Pin: NB2-2XP:
SS Clevis Pin is 10mm (3/8") diameter with a 1 5/16" (33mm) grip length. Includes SS Cotter Ring.
|
||
|
NB2 Horizontal Gooseneck Bolt w/ Locknut: NB2-3XA:
SS Bolt is 10mm (3/8") dia. x 40mm (1 5/8") long. Used to attach the Isomat Gooseneck Toggle (NB2-2X) to Old-Style NB-32 Gooseneck Casting. Includes 10mm SS Locknut.
|
||
|
NB-32 Old-Style Gooseneck Sheave: NB2-10XA:
Anodized Aluminum Sheave is 50mm (2") OD x 14mm (9/16") wide x 10mm (3/8") ID with a deep groove. Replaces earlier Acetyl version, NB2-10X.
|
||
|
Sheave/Cam Axle for NB-32 Old-Style Gooseneck: NB2-12X:
SS knurled axle pin is 10mm (3/8") dia. x 90mm (3 9/16") long.
|
|
|
|
Large Gooseneck Cam – Old Style Curved: NB2-14XC:
Old-Style gooseneck Cam lever with curved handle used in NB-32, NB-40, and NB-55 Old-Style goosenecks. Cast aluminum cam measures (max.) 4 3/4" long x 9/16" wide (120 x 14mm), and rides on 10mm (3/8") cam axle.
|
|
|
|
Large Gooseneck Cam – Old Style Straight: NB2-14XS: Old-Style gooseneck Cam lever with straight handle used in NB-32, NB-40, and NB-55 Old-Style goosenecks. Cast aluminum cam measures (max.) 4 7/8" long x 9/16" wide (123 x 14mm), and rides on 10mm (3/8") cam axle.
|
|
|
~ Home ~
