 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Pearson Yachts RR #3522 Boom Section |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Pearson Yachts RR #3522 Boom Section |
|
|
|
|
| Pearson Yachts RR #3522 Boom Measurements: (OD) 3.50" x 2.20" Wall Thickness: .100" Weight/ft.: 1.4 lbs. Circumference: 8 7/8" Alloy: 6063-T6 Sail slides: 1/2" round slugs (A018, A118) or 1/2" boltrope Common Boom usage: Pearson 22*, Electra*, Ensign*, Tiger Cat, Triton*; - At one time Pearson used the RR #3522 Boom on most all of their boats up to 28'. Common Mast usage: Pearson Hawk, Triton Yawl Mizzen Mast |
|
|
|
|
| RR #3522 Boom Section Rig-Rite #3522 Boom Section is no longer available. For Replacement Booms, Pearson Yachts RR #4025 Section is recommended, as it is available in identical configurations, will fit the same Mast connections, and is aesthetically similar. See Pearson Yachts RR #4025 Boom Section. |
|
|
|
|
| RR #3522 Standard Boom Hardware Listed below are parts specific to the Rig-Rite #3522 Boom Section. For more generic parts, see categories listed under Spar Parts. There are many parts for specific configurations that are not listed here. If you require Rig-Rite #3522 Boom Components not listed here please contact us with details. |
|
|
|
|
| RR #3522 Gooseneck Assemblies & Parts Original RR #3522 Goosenecks used by Pearson and Bristol Yachts were of the Roller Reefing variety. A spring-loaded Aluminum shaft fits into a recess in the boom casting, Reefing is accomplished by pulling aft on the boom and rolling it and the sail at the same time. All parts are listed here, as well as substitutes for all standard configurations, but the original 3522 Boom Gooseneck casting to fit the 3/4" Roller Reefing Gooseneck Shaft is no longer available.
|
|
| Gooseneck Assembly w/ 1 1/2" Toggle: PP 3522-3ATL:
Cast aluminum Gooseneck fitting for RR #3522 Boom includes captive SS tack pin, and 1 1/2" extruded Toggle (PP B4). Toggle is suitable for use with any Gooseneck Slide or Bracket designed for a 1 1/2" Toggle and a 1/4" vertical Pin. Captive SS tack pin is superior to original Pearson threaded Tack Pin which was easily misplaced. Note: New-style Gooseneck has integral cast nose, replacing earlier Roller Reefing version Gooseneck. Old-Style Roller Reefing Gooseneck used the Roller Reefing Gooseneck Shaft Assembly which is still available, see below. Order Gooseneck Slides separately, see below.
|
 |
|
| Gooseneck Ass'y w/ Tack Pin: PP 3522-3:
Cast aluminum Gooseneck fitting for RR #3522 Boom includes captive SS Tack Pin and has integral cast nose with 1/4" horizontal hole to fit special extruded Toggles (PP B4, PP B4X), listed below. Captive SS Tack Pin is superior to original Pearson threaded Tack Pin which was easily misplaced. Note: New-style fixed Gooseneck replaces earlier Roller Reefing version Gooseneck. Old-Style Roller Reefing Gooseneck used the Roller Reefing Gooseneck Shaft Assembly which is still available, see below.
|
 |
|
| Threaded Tack Pin: PP B34526:
Early versions of this Gooseneck Assembly used a non-captive 1/4" threaded Tack Pin.
|
 |
|
| Roller Reefing Gooseneck Shaft Ass'y w/ Spring & Toggle: PP B2AST: | ||
| Roller Reefing Gooseneck Shaft Assembly with Spring and 1
1/2" extruded Toggle (PP B4) is used on boom ends with an
oval recess in forward end. Toggle is suitable for use with any Gooseneck Slide or bracket
designed for a 1 1/2" Toggle and a 1/4" vertical Pin. Note:
Gooseneck Shaft can be drilled for additional Cotter Pin hole immediately behind Boom End
Casting (and used without Spring) to eliminate Roller Reefing feature.
Note: the original 3522 Boom Gooseneck casting to fit the 3/4" Roller
Reefing Gooseneck Shaft is no longer available.
|
||
| Roller Reefing Gooseneck Shaft Ass'y w/ Toggle: PP B2AT: | ||
| Roller Reefing Gooseneck Shaft Assembly with 1 1/2" extruded Toggle (PP B4)
is used on boom ends with an oval recess in forward end. Toggle is suitable for use with
any Gooseneck Slide or bracket designed for a 1 1/2" Toggle and a 1/4" vertical
Pin. Note: Gooseneck Shaft can be drilled for additional Cotter Pin hole
immediately behind Boom End Casting (and used without Spring) to eliminate Roller Reefing feature.
|
|
|
|
|
Roller Reefing Gooseneck Shaft (Arrowhead): PP B2:
Roller Reefing Gooseneck Shaft used on boom ends with an oval recess in forward end. Cast aluminum unit is 4 1/4" long with 3/4" diameter shaft, shaft is 2 3/4" long. Nose is 1 1/2" high x 7/16" wide with hole for 1/4" pin. For use with special Extruded Gooseneck Toggles, listed below. Note: Gooseneck Shaft can be drilled for additional Cotter Pin hole immediately behind Boom End Casting (and used without Spring) to eliminate Roller Reefing feature.
|
|
| Extruded Gooseneck Toggle - 1 1/2": PP B4:
Extruded Gooseneck Toggle for use with aluminum Roller Reefing Gooseneck Shaft, or boom ends with integral nose. Aluminum Gooseneck Toggle is 1 1/2" high x 3/4" wide with (2) holes for 1/4" vertical and horizontal pins, horizontal pin is included. Aft end has 1/2" wide cutout for PP B2 Gooseneck Shaft or boom ends with integral nose. Toggle is suitable for use with any Gooseneck Slide or bracket designed for a 1 1/2" Toggle and a 1/4" vertical Pin.
|
|
|
| Short Extruded Gooseneck Toggle - 7/8": PP B4X:
Old-style, short Extruded Gooseneck Toggle for use with aluminum Roller Reefing Gooseneck Shaft, or boom ends with integral nose. Aluminum Gooseneck Toggle is 7/8" high x 3/4" wide with (2) holes for 1/4" vertical and horizontal pins, horizontal pin is included. Aft end has 1/2" wide cutout for PP B2 Gooseneck Shaft or boom ends with integral nose. Short Toggle fits old-style Gooseneck Slides with 1" cutout.
|
|
|
| Roller Reefing Gooseneck Shaft Spring: PP B3:
SS Spring for use with Aluminum 3/4" Roller Reefing Gooseneck Shaft. SS Spring is 1" OD x 2 3/4" long (uncompressed).
|
||
|
Gooseneck Slide for Boltrope & 1 1/2" Toggle: PP M5A:
Extruded Gooseneck Slide fits RR #4025 Mast Section, and some other Teardrop-shaped mast sections with a 1/2" boltrope groove. Aluminum Gooseneck Slide is 3" high x 5/8" wide and uses a 1/4" vertical pin. Aft side has 1 5/8" cutout for Gooseneck Toggle, and features 1/4" hole for downhaul line or shackle. Includes vertical Pin and nylon washers to eliminate chafe against Toggle. As used on Ensign, Electra and others.
|
 |
|
| Gooseneck Slide for 3/4" Internal Flat Track & 1 1/2" Toggle: PP M6A: | ||
| Aluminum Gooseneck Slide fits most
Mast Sections with a 3/4" flat internal track. Gooseneck Slide is 4" high x
3/4" wide and uses a 1/4" vertical pin. Aft side has 1 5/8" cutout for
Gooseneck Toggle, and features 5/16" hole for downhaul line or shackle. Includes
vertical Pin and nylon washers to eliminate chafe against Toggle. As used on Pearson 26
and others. *
|
 |
|
|
|
||
| RR #3522 Bails and Vang Fittings | ||
| Boom Bail - 1/4" x 2 1/4" wide: K-10456:
Heavy SS Boom Bail made from 1/4" rod is designed to be attached with (1) 1/4" SS bolt and nut. Formed at 2 1/4" wide, width can be varied to fit larger or smaller sections. Bail length, from bolt center, is 2 1/2". For use with RR #3522 boom.
|
 |
|
| Boom Bail Bolt Ass'y - 1/4" for #3522: K-10456BA:
Boom Bail bolt assembly includes 1/4" SS bolt x 2 3/4", with locknut, and nylon washers to prevent bail from damaging boom surface as it pivots.
|
 |
|
| Boom Vang Ball Attachment Plate for #3522 Boom: K-2182:
Formed SS plate for attachment of Boom Vang with 1/8" wire swage ball. Allows for quick attachment and removal of Boom Vang, raised channel design allows easy installation without milling slot in boom. Channel projects approximately 3/8" from underside of Boom when installed. Formed Stainless Steel plate is 2" long x 1 7/8" high. Fastens with (6) 3/16" (#10) screws or rivets.
|
||
| Boom Vang Ball Attachment Plate, Flush Mount: K-2182F:
Formed SS plate for attachment of Boom Vang with 1/8" wire swage ball. Allows for quick attachment and removal of Boom Vang, flush mounting design allows use with Roller-Reefing booms. Base is curved to fit a variety of Boom Sections, narrow profile allows it to be bent to fit others. Formed Stainless Steel plate is 3" long x 1 1/2" wide. Mounting requires 3/8" wide x 1 1/4" long slot in Boom. Fastens with (6) 3/16" (#10) screws or rivets.
|
 |
|
|
|
Boom Vang Wire Pennant w/ Swage Ball: K-2182WP:
Wire Pennant for attachment of Boom Vang to Boom Vang Ball Attachment Plate. Pennant is 1/8" wire with swage ball and shank (MS20664-4) on one end and a nicopress and thimble on the other. Thimble allows attachment of any upper Vang block. Assembly is 6" long. Ball is suitable for all Ball Attachment Plates with a slot that is 1/4" wide or less.
|
|
|
|
||
| RR #3522 Outhaul Fittings | ||
| Outhaul Cap: PP 3522-4:
Cast aluminum Outhaul Cap for RR #3522 Boom covers outboard boom end.
|
 |
|
| Outhaul Cap w/ 2 Tangs: PP 3522-4-2:
Cast aluminum Outhaul Cap for RR #3522 Boom covers outboard boom end and includes 2 swiveling tangs for mainsheet and/or topping lift attachment. Swiveling attachments for mainsheet and topping lift are required for use with roller-reefing goosenecks.
|
|
|
| Outhaul Lug: PP B10:
Extruded aluminum Outhaul Lug has tab with 2 holes for outhaul, and/or topping lift attachment. Lug is 1 1/2" long and fits any Boom Section with a 1/2" Boltrope groove. Lug slides into groove and is secured at outboard end with a screw through boom wall into lug. |
 |
|
~ Back to Pearson Booms Main Page ~
~ Home ~