 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z65 Spreaders and Components |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z65 Spreaders and Components |
|
|
|
|
| Z-Spar Z65 Spreader Section Outside Measurements: 56mm x 20.5mm (2 3/16" x 13/16") Inside Measurements: 52mm x 17mm (2 1/16" x 11/16") Wall thickness: 1.8mm Weight/M.: 0.5kg. - Weight/ft.: 0.34 lbs. |
|
|
The Z65 Spreader Section has interior dimensions that are very similar to the Z95 Spreader.
Additional fittings used with this Spreader Section are listed under the Z95 Spreader Section. Please note that Z65 Spreaders can not be tapered. |
|
|
|
|
|
Z65 Standard Spreader Assembly: Z-65AS-____: Standard Z65 Spreader Assembly is clear anodized and includes Z-3114 Spreader Tip. To order specify maximum tube length, and sweepback angle (if any). If other Tip or any inboard end is required, specify Part Number(s).
|
|
|
Z65 Standard Spreader - Tube only, Drilled: Z-65T-____: For replacement purposes when using original end fittings, Z65 Spreader Tubes are available anodized and drilled for Z-3114 Spreader Tip, and with inboard angles cut. To order specify maximum tube length, and sweepback angle (if any).
|
|
|
Z65 Spreader Section, Clear Anodized: Z-65CA-____: Z65 Spreader Section is available clear anodized, but without drilling or angles cut at lengths up to 20'. To order specify maximum length.
|
|
|
|
||
| Spreader Tips & Components for Z65 Spreaders | ||
|
J-Bolt Tips require that the Tip be removed from the Spreader to
adjust Clamp tension. |
||
|
Spreader Tip Ass'y for Z65 Spreader: Z-3114:
Gray plastic Spreader Tip for use with Z65 Spreader. Includes 6mm J-bolt with locknut, Z-1481A, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 2 7/16" long x 1 1/8" wide (62mm x 29mm). This item is no longer available, having been replaced by the Z-3114NC, below.
|
|
|
|
|
J-bolt w/ Locknut for Z65 Spreader Tip: Z-1481A:
SS J-bolt is 2" (50mm) long with a 6mm thread and includes SS locknut. For use with Z-3114 Spreader Tip.
|
|
|
C-Clamp type Tips allow adjustment of Clamp tension without
removing the Tip from the Spreader. |
||
|
Spreader Tip Ass'y for Z65 Spreader: Z-3114C:
Gray plastic Spreader Tip for use with Z65 Spreader. Includes C-Clamp with screw, Z-1481CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 2 7/16" long x 1 1/8" wide (62mm x 29mm). This item is no longer available, having been replaced by the Z-3114NC, below.
|
|
|
|
Spreader Tip Ass'y for Z65 Spreader: Z-3114NC:
New-style Gray plastic Spreader Tip for use with Z65 Spreader. Includes C-Clamp with screw, Z-1481CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 2 7/16" long x 1 1/8" wide (62mm x 29mm).
|
|
|
|
|
C-Clamp w/ Screw for Z65 Spreader Tip: Z-1481CA:
SS C-Clamp with 6mm socket head screw is used to clamp shroud to the spreader tip. For use with Z-3114C and Z-3114LC Spreader Tips.
|
|
| Discontinuous Tips | ||
|
Discontinuous Spreader Tip for Z65 w/ 8mm Pin: Z-1039-8A:
Discontinuous Spreader Tip for Z65 w/ 10mm Pin: Z-1039-10A: Assembly provides horizontal pin for attachment of Discontinuous Shrouds. Includes anodized cast aluminum tip with horizontal pin and cotter pin. Unit projects (maximum) 1 1/16" (27mm) from end of spreader tube. Slot width (at pin) is 1 3/16" (30mm), pin center is 5/8" (16mm) from tube end.
|
|
|
|
|
8mm Pin for Z-1039 Tip Casting: Z-1040P-8:
10mm Pin for Z-1039 Tip Casting: Z-1039P-10: SS Pins only for Z-1039 Discontinuous Spreader Tip Assemblies, above. Pins are 53mm (2 1/16") long. =1039P
|
|
|
Discontinuous Tip Ass'y for Z65 - 8mm/6mm: Z-1042L-86:
Cast aluminum Spreader Tip incorporates an 8mm Pin outboard for the main shrouds, and a 6mm inboard Pin for intermediate shrouds. Unit projects (maximum) 2" (50mm) from end of spreader tube. Slot width (at outboard pin) is 3/4" (20mm), pin center is 1 1/4" (32mm) from tube end. Inboard Pin (6mm) has slot width of 5/16" (8mm), pin center is 1/2" (12mm) from tube end. Pins are included.
|
|
|
|
|
6mm Pin for Z-1042 Tip Casting: Z-1042P-6:
8mm Pin for Z-1042 Tip Casting: Z-1042P-8: SS Pins only for Z-1042 Discontinuous Spreader Tip Assembly, above. Pins are 38mm (1 1/2") long.
|
|
|
|
||
| Spreader Bases for Z65 Spreaders | ||
|
Spreader Base for Z170 Mast & Z65 Spreaders: Z-170SB-2:
Wrap-around Spreader Base for Z170 Mast Section and Z60 or Z65 Spreaders. Cast aluminum base holds both spreaders and accommodates a variety of spreader angles. Spreaders are attached with 6mm (1/4") bolts (2 each), unit attaches to Mast with (6) 5mm (3/16") screws or rivets.
|
|
|
|
Spreader Base for Z190 Mast & Z65 Spreaders: Z-190SB-2:
Wrap-around Spreader Base for Z190 Mast Section and Z60 or Z65 Spreaders. Cast aluminum base holds both spreaders and accommodates a variety of spreader angles. Spreaders are attached with 8mm (5/16") bolts (2 each), unit attaches to Mast with (6) 5mm (3/16") screws or rivets.
|
|
|
|
Spreader Base for Z230 Mast & Z65 Spreaders: Z-230SB-2:
Wrap-around Spreader Base for Z230 Mast Section and Z60 or Z65 Spreaders. Cast aluminum base holds both spreaders and accommodates a variety of spreader angles. Spreaders are attached with 8mm (5/16") bolts (2 each), unit attaches to Mast with (6) 5mm (3/16") screws or rivets.
|
|
|
|
|
||
| Spreader Bases & Bars for Z65 Spreaders | ||
| A variety of other Spreader Bases, Bars, and Inboard Spreader Ends are sometimes used with Z65 Spreaders. See: Z95 Spreaders. | ||
~ Back to Z-Spar Spreader Page ~
~ Home ~
