Your cart

Total
CAD
Shipping and discount codes are added at checkout.

Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
 Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com          Ordering/Questions

Z95 Spreaders and Components
Z-Spar Z95 Spreader Section
Outside Measurements (Untapered): 80mm x 25mm (3 1/8" x 1")
Inside Measurements: 52mm x 17mm (2 1/16" x 11/16")
Wall thickness: 2mm
Weight/M.: 1.25kg. - Weight/ft.: 0.84 lbs.
 
The Z95 Spreader Section features an integral "tail", so that the Spreaders (as an option) can be tapered at the outboard end without welding. Z95 Spreader Assemblies are available in Standard (untapered), and Tapered versions with a variety of inboard and outboard end fittings, listed below.
The Z80 Spreader Section has dimensions that are similar to the Z95 Spreader (but w/o the 'Tail'), fitting all the same Spreader Bars and (un-tapered) Spreader Tips as the Z95 Spreader.
 
Z95 Standard Untapered Spreader Assembly: Z-95AS-xxx:

Z95 Standard Untapered Spreader Ass'y - Angled Aft: Z-95ASA-xxx:

Standard Untapered Z95 Spreader Assembly is clear anodized and includes Z-3114L Spreader Tip. To order specify maximum tube length up to 1M (39"), and sweepback angle (if any). If an inboard end is required, order separately, below.

 
Z95 Standard Untapered Spreader Tube only: Z-95T-xxx:

Z95 Standard Untapered Spreader Tube only - Angled Aft: Z-95TAA-xxx:

Standard Untapered Z95 Spreader Tube is clear anodized. To order specify maximum tube length up to 1M (39"), and sweepback angle (if any).

 
Z95 Tapered Spreader Assembly Standard: Z-95AT-xxx:

Z95 Tapered Spreader Ass'y Standard - Angled Aft: Z-95ATAA-xxx:

Z95 Tapered Spreader Ass'y w/ Discontinuous Tip 10/8mm: Z-95AT10/8-xxx:

Z95 Tapered Spreader Ass'y w/ Discontinuous Tip 12/8mm: Z-95AT12/8-xxx:

Standard Tapered Z95 Spreader Assembly is clear anodized and includes Z-3114 Spreader Tip. To order specify maximum tube length, and sweepback angle (if any). If other Tip or any inboard end is required, specify Part Number(s). Discontinuous Tapered Z95 Spreader Assembly is clear anodized and includes Z-1040-108 or Z-1040-128 Spreader Tip. To order specify maximum tube length, and sweepback angle (if any). If other Tip or any inboard end is required, specify Part Number(s).

 
Z95 Tapered Spreader - Tube only, Tapered & Drilled: Z-95TT-xxx:

Z95 Tapered Spreader - Tube only, Tapered & Drilled - Angled Aft: Z-95TTAA-xxx:

For replacement purposes when using original end fittings, Z95 Spreader Tubes are available Tapered and drilled for Z-3114 Spreader Tip, and with inboard angles cut. To order specify maximum tube length up to 1M (39"), and sweepback angle (if any). Clear anodized finish is standard.

 
Z95 Spreader Section, Clear Anodized: Z-95CA-____:
Z95 Spreader Section is available clear anodized, but without taper or drilling at lengths up to 20'. To order specify maximum length.

 
Spreader Tips & Components for Z95 Spreaders
J-Bolt Tips require that the Tip be removed from the Spreader to adjust Clamp tension.
 
Spreader Tip Ass'y for Z95 Standard Spreader: Z-3114L:

Gray plastic Spreader Tip for use with Standard Untapered Z95 Spreader. Includes 6mm J-bolt with locknut, Z-1481A, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 3 5/16" long x 1 1/8" wide (84mm x 29mm).

 

Spreader Tip Ass'y for Z95 Tapered Spreader: Z-3114:

Gray plastic Spreader Tip for use with Tapered Z95 Spreader. Includes 6mm J-bolt with locknut, Z-1481A, to clamp shroud to the spreader tip prior to installation in the spreader tube. When used with hinged spreader bases, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 2 7/16" long x 1 1/8" wide (62mm x 29mm).

 

Z-3114
J-bolt w/ Locknut for Z95 Spreader Tip: Z-1481A:

SS J-bolt is 2" (50mm) long with a 6mm thread and includes SS locknut. For use with Z-3114 and Z-3114L Spreader Tips.

 

Z-1481A
C-Clamp type Tips allow adjustment of Clamp tension without removing the Tip from the Spreader.
 
Spreader Tip Ass'y for Z95 Standard Spreader: Z-3114LC:

Gray plastic Spreader Tip for use with Standard Untapered Z95 Spreader. Includes C-Clamp with screw, Z-1481CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 3 5/16" long x 1 1/8" wide (84mm x 29mm).

 

  
Spreader Tip Ass'y for Z95 Tapered Spreader: Z-3114C:

Gray plastic Spreader Tip for use with Tapered Z95 Spreader. Includes C-Clamp with screw, Z-1481CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 2 7/16" long x 1 1/8" wide (62mm x 29mm). This item is no longer available, having been replaced by the Z-3114NC, below.

 

  
Spreader Tip Ass'y for Z95 Tapered Spreader: Z-3114NC:

New-style Gray plastic Spreader Tip for use with Tapered Z95 Spreader. Includes C-Clamp with screw, Z-1481CA, to clamp shroud to the spreader tip. When installed, clamp must be tight and positioned carefully on the shroud. Tip is (maximum) 2 7/16" long x 1 1/8" (62mm x 29mm).

 

  
C-Clamp w/ Screw for Z95 Spreader Tip: Z-1481CA:

SS C-Clamp with 6mm socket head screw is used to clamp shroud to the spreader tip. For use with Z-3114C, Z-3114LC and Z-3114NC Spreader Tips. Cast Clamp is marked 4234.

 

 
Discontinuous Tips
Discontinuous Tip Ass'y for Z95 - 8mm/6mm: Z-1042L-86:

Cast aluminum Spreader Tip for use with Tapered Z95 Spreader incorporates an 8mm Pin outboard for the main shrouds, and a 6mm inboard Pin for intermediate shrouds. Unit projects (maximum) 2" (50mm) from end of spreader tube. Slot width (at outboard pin) is 3/4" (20mm), pin center is 1 1/4" (32mm) from tube end. Inboard Pin (6mm) has slot width of 5/16" (8mm), pin center is 1/2" (12mm) from tube end. Pins are included.

 

 

 

 6mm Pin for Z-1042 Tip Casting: Z-1042P-6:

8mm Pin for Z-1042 Tip Casting: Z-1042P-8:

SS Pins only for Z-1042 Discontinuous Spreader Tip Assembly, above. Pins are 38mm (1 1/2") long.

 

Z-1042P-8
Discontinuous Spreader Tip for Z95 w/ 8mm Pin: Z-1039-8A:

Discontinuous Tip for Z95 w/ 10mm Pin: Z-1039-10A:

Cast aluminum Spreader Tip for use with Tapered Z95 Spreader includes horizontal pin and cotter pin. Unit projects (maximum) 1 1/16" (27mm) from end of spreader tube. Slot width (at pin) is 1 3/16" (30mm), pin center is 5/8" (16mm) from tube end.

 

Z-1039-10
 

 

 8mm Pin for Z-1039 Tip Casting: Z-1040P-8:

10mm Pin for Z-1039 Tip Casting: Z-1039P-10:

SS Pins only for Z-1039 Discontinuous Spreader Tip Assemblies, above. Pins are 53mm (2 1/16") long. =1040P

 

Z-1039P-10
Discontinuous Spreader Tip for Z95 - 8mm/8mm: Z-1040-88:

Discontinuous Tip for Z95 - 10mm/8mm: Z-1040-108:

Discontinuous Tip for Z95 - 12mm/8mm: Z-1040-128:

Discontinuous Tip for Z95 - 10mm/10mm: Z-1040-1010:

Discontinuous Tip for Z95 - 12mm/10mm: Z-1040-1210:

Cast aluminum Spreader Tip Assembly for use with Tapered Z95 Spreader includes an 8, 10, or 12mm Pin outboard for the main shrouds, and an 8 or 10mm inboard Pin for intermediate shrouds. Unit projects (maximum) 2 3/4" (70mm) from end of spreader tube. Slot width (at outboard pin) is 1 1/8" (28mm), pin center is 1 1/2" (38mm) from tube end. Inboard Pin has slot width of 7/16" (11mm), pin center is 1/2" (12mm) from tube end.

 

Z-1040-88

 
8mm Pin for Z-1040 Tip Casting: Z-1040P-8:

10mm Pin for Z-1040 Tip Casting: Z-1040P-10:

12mm Pin for Z-1040 Tip Casting: Z-1040P-12:

SS Pins only for Z-1040 Discontinuous Spreader Tip Assemblies, above. 10mm & 12mm Pins are 57mm (2 1/4") long. 8mm Pin is 53mm (2 1/16") long.

 

 Z-1040P-8

 
Discontinuous Tip for Z95 - 10mm/8mm: Z-1040NT-108:

Discontinuous Tip for Z95 - 12mm/8mm: Z-1040NT-128:

Cast aluminum Spreader Tip Assembly for use with Standard Untapered Z95 Spreader. Incorporates an 8, 10, or 12mm Pin outboard for the main shrouds, and an 8 or 10mm inboard Pin for intermediate shrouds. Unit projects (maximum) 2 3/4" (70mm) from end of spreader tube. Slot width (at outboard pin) is 1 1/8" (28mm), pin center is 1 1/2" (38mm) from tube end. Inboard Pin has slot width of 7/16" (11mm), pin center is 1/2" (12mm) from tube end. Pins (included) are as Z-1040P, above.

 

 
Inboard Spreader Ends & Spreader Bases for Z95 Spreaders
 

 

Inboard Hinge End for Z95 Spreader - 0° aft: Z-1211-0:

Inboard Hinge End for Z95 Spreader - 5° aft: Z-1212-5:

Inboard Hinge End for Z95 Spreader - 10° aft: Z-1213-10:

Inboard Hinge End for Z95 Spreader - 15° aft: Z-1214-15:

Inboard Hinge End for Z95 Spreader - 18° aft: Z-1215-18:

Inboard Hinge End for Z95 Spreader - 28° aft: Z-1216-28:

Special Inboard Hinge Ends are used to attach Z95 Spreader to hinged Spreader Base using 10mm SS Pin. Units are available with a variety of standard angles built in for swept back spreaders. Cast aluminum unit is 2 5/16" wide x 15/16" thick at Pin hole. SS 10mm Hinge Pin is not included, See Z-1336X, or Z-1318X, below.
Items listed as "Out" are no longer available.

 

Z-1211-0

Z-1216-28
Hinged Spreader Base w/ Tangs for Z95 Spreaders for 8mm Pins: Z-1022-8:

Hinged Spreader Base w/ Tangs for Z95 Spreaders for 10mm Pins: Z-1022-10:
Unique design incorporates double lower shroud tangs into a hinged spreader base assembly. Clevis pins, without holes, are prevented from moving once spreaders are attached. Base is 3 1/2" high x (maximum) 4 1/4" wide, and attaches to mast with (5) 1/4" (6mm) rivets. Used on Z265, Z300, Z301 and other mast sections. Shown with Z-1336X Hinge Pin and Z-1022P Shroud Pins (order separately). These items are no longer available and are shown here for identification only.

 

 Z-1035
Shroud Clevis Pin for Z95 Spreader Base - 8mm: Z-1022P-8:

Shroud Clevis Pin for Z95 Spreader Base - 10mm: Z-1022P-10:
Special SS Clevis pins (without holes) hold shrouds in place and are prevented from moving once spreaders are attached. Pins must be the same diameter as the hole in the Spreader Base. Pins are 24mm (15/16") long (under head). For use with Z-1022 Spreader Bases.

 
Hinge Pin for Z95 Spreader Base: Z-1336X:

Hollow SS Pin is held in place with a single cotter pin. Pin measures 10mm x 80mm (3 1/8") long. For use with Z-1022 Spreader Bases.

 
Hinged Spreader Base w/ Tangs for Z95 Spreaders for 12mm Pins: Z-1035-12:
Unique design incorporates double lower shroud tangs into a hinged spreader base assembly. 12mm Clevis pins, without holes, are prevented from moving once spreaders are attached. Base is 4 1/8" high x (maximum) 5" wide, and attaches to mast with (5) 1/4" (6mm) rivets. Used on Z400, Z401, Z500, Z501 and other mast sections. Other Clevis Pin sizes available, Please specify. Shown with Z-1318X Hinge Pin and Z-1035P Shroud Pins (order separately). These items are no longer available and are shown here for identification only.

 

Z-1035
Shroud Clevis Pin for Z95 Spreader Base - 12mm: Z-1035P-12:
Special SS Clevis pins (without holes) hold shrouds in place and are prevented from moving once spreaders are attached. Pins must be the same diameter as the hole in the Spreader Base. Pins are 28mm (1 1/8") long (under head). For use with Z-1035 Spreader Bases.

 
Hinge Pin for Z95 Spreader Base: Z-1318X:

Solid SS Pin is held in place with a single cotter pin. Pin measures 10mm x 86mm (3 3/8") long. Note: Replaces original factory part made from light-duty hollow Tube. For use with Z-1035 Spreader Bases.

 
Old-style Spreader Base for Z95 Spreaders: Z-1025X:

Old-style Spreader Base for Z95 Spreaders accommodates a variety of spreader angles. The same base is used on both sides of the mast, but spreaders must be drilled differently port and starboard to achieve a vertical angle. Spreader is attached with (2) 10mm clevis pins. Cast aluminum Spreader Base is (maximum) 144mm (5 5/8") long x 52mm (2") high, and attaches to Mast with (5) 5mm (3/16") rivets. Used on Z300 and other obsolete Mast Sections, Please specify Mast Section when ordering. Part is marked 1025.

 

Z-1025 

 
Old-style Spreader Base for Z95 Spreaders: Z-1027X:

Old-style Spreader Base for Z95 Spreaders accommodates a variety of spreader angles. The same base is used on both sides of the mast, but spreaders must be drilled differently port and starboard to achieve a vertical angle. Spreader is attached with (2) 10mm clevis pins. Cast aluminum Spreader Base is (maximum) 152mm (6") long x 57mm (2 1/4") high, and attaches to Mast with (5) 5mm (3/16") rivets. Used on Z320 and other obsolete Mast Sections, Please specify Mast Section when ordering. Part is marked 1027.

 

 

 

 
Spreader Bars for Z95 Spreaders
SS Spreader Bars for Z95 Spreaders
Solid SS Spreader Bars for Z95 Spreaders are 16mm thick x 26mm wide (5/8" x 1"), and available formed in a variety of angles.

 
SS Spreader Bar for Z95 - 0° aft: Z-1680-0:
SS Spreader Bar for Z95 - 15° aft: Z-1679-15:

SS Spreader Bar for Z95 - 22° aft: Z-1678-22:
SS Spreader Bar for Z95 - 30° aft: Z-1678-30:

Solid SS Spreader Bar (Z-1600-Series) for Z95 Spreader is 5/8" thick x 1" wide (16mm x 26mm), and available in a variety of angles not listed here. Used with Z-1347S, and Z-1703L SS Reinforcing Plates. When ordering please specify Mast Section and spreader angle (if any).

 

 Z-1678-22
SS Reinforcing Plate for Z95 SS Spreader Bar: Z-1347S:
SS Plate is formed to fit the mast section and features boss to allow a straight cut on the spreader end. Slot in plate is 5/8" x 1 5/16" long (16mm x 33mm). Plates (2 required) are attached to the mast with (4) 3/16" rivets. For use with Z265, Z290, & Z300 Mast sections.

 

Z-1347
SS Reinforcing Plate for Z95 SS Spreader Bar: Z-1703L:

SS Plate is formed to fit the mast section and features boss to allow a straight cut on the spreader end. Slot in plate is 5/8" x 1 5/16" long (16mm x 33mm). Plates (2 required) are attached to the mast with (4) 3/16" rivets. For use with Z301, Z320, Z380, Z400, Z401, Z500, Z501, & Z531 Mast sections.

 
Aluminum Spreader Bars for Z95 Spreaders
Extruded Aluminum Spreader Bars for Z95 Spreaders feature a slot for a SS Fixing Plate to secure the Spreaders in place.

 
Aluminum Spreader Bar for Z95 - 0° aft: Z-5095-0:

Aluminum Spreader Bar for Z95 - 5° aft: Z-5088-5:

Aluminum Spreader Bar for Z95 - 10° aft: Z-5089-10:

Aluminum Spreader Bar for Z95 - 15° aft: Z-5090-15:

Aluminum Spreader Bar for Z95 - 20° aft: Z-5091-20:

Aluminum Spreader Bar for Z95 - 25° aft: Z-5093-25:

Aluminum Spreader Bar for Z95 - 30° aft: Z-5092-30:

Extruded Aluminum Spreader Bar for Z95 Spreaders is 5/8" thick x 1 9/16" wide (16mm x 40.5mm) with a 16mm (5/8") wide slot, and is available in a variety of angles. Used with a variety of Aluminum Reinforcing Plates. When ordering please specify Mast Section and spreader angle (if any).

 

  
Fixing Plate for Z95 Alu. Spreader Bar - 10mm: Z-53AX:

SS Fixing Plate for Z95 Old-style Aluminum Spreader Bar with 11mm (7/16") wide slot. SS Plate is 10mm wide x 4mm thick x 100mm long (3/8" x 3/16" x 4") with (2) 6mm tapped holes on 70mm centers. Includes (2) 6mm x 16mm screws.

 
Fixing Plate for Z95 Alu. Spreader Bar - 15 mm: Z-4734A:

SS Fixing Plate for Z95 Aluminum Spreader Bar with 16mm (5/8") wide slot. SS Plate is 15mm wide x 6mm thick x 100mm long (5/8" x 1/4" x 4") with (2) 6mm holes on 70mm centers, (1) hole is tapped. Includes (1) 6mm x 16mm screw.

 
Reinforcing Plate for Z95 Alu. Spreader Bar: Z-5097:

Aluminum Plate is formed to fit the mast section and features boss to allow a straight cut on the spreader end. Plate is 5" long x 2 7/16" (maximum) wide, slot in plate is 5/8" x 1 5/8" long (16.5mm x 42mm). Plates (2 required) are attached to the mast with (6) 3/16" rivets. For use with Z401 & Z501 Mast sections for Bars up to 15° aft.

 

Reinforcing Plate for Z95 Alu. Spreader Bar: Z-5086:

Aluminum Plate is formed to fit the mast section and features boss to allow a straight cut on the spreader end. Plate is 5" long x 2 7/16" (maximum) wide, slot in plate is 5/8" x 1 7/8" long (16.5mm x 48mm). Plates (2 required) are attached to the mast with (6) 3/16" rivets. For use with Z401 & Z501 Mast sections for Bars from 20° to 30° aft.

 

~ Back to Z-Spar Spreader Page ~

~ Back to Z-Spar Main Page ~

~ Home ~