Kenyon BW Harpoon 5.2 Mast & Components

Common Replacement Parts are listed below.
Additional specifications and photographs of all components listed below, as well as details of the Spar Sections and additional parts, are available on the Spar Section, or Parts pages.

Harpoon 5.2 Masts now use the Kenyon 2331 Mast Section.
        though early models used the Kenyon G Mast Section (discontinued).
Harpoon 5.2 Booms use the Kenyon 2331 Boom.
        though early models used the Kenyon B Section. See Kenyon B Boom Section for Parts.
Harpoon 5.2 Spreaders use either the Kenyon 5/8" OD Spreader Section,
        OR the Kenyon SP-1 Airfoil Spreader Section.

Description	Part #
Harpoon 5.2 Mast Assembly - 2331 Section w/ New-Style	: K-FM535A:
Masthead and 5/8" OD Spreaders - Clear Anodized 1359
Harpoon 5.2 Mast Kit - 2331 Section x 24' 7 1/2" w/ Gate milled,	: K-FMK535A:
all Hardware w/ New-Style Masthead and 5/8" OD Spreaders
- Clear Anodized
Harpoon 5.2 Mast Tube - 2331 Section x 24' 9 1/2" (max. long)	: K-FMT535A:
w/ gate milled - Clear Anodized - (Tube 24' 7 1/2", 4" Gate @ 4' 2")

Masthead Ass'y - New-Style - External Casting w/ Removable Sheaves	: K-2331EH:
Masthead Ass'y - Old-Style - Inset Channel	: K-40521:
Masthead Cap - Old-Style - for Inset Channel Masthead	: K-10329:
Main Halyard Sheave - Aluminum 1" OD 1/4" ID	: K-198-4A:
Main Halyard Sheave - Plastic 1 1/16" OD 1/4" ID	: K-199-3A:
Main halyard sheave Axle - Clevis Pin 1/4"	: CP4-26K:

Forestay/Shroud Tang (3 required)	: K-354-4:
Eyestrap for Spinnaker Halyard & Pole Blocks (3 required)	: K-226:
Eyestrap for Jib Halyard Block (4-hole)	: K-226-4:
Jib/Spinnaker Halyard Block, Pole Lift Block - Aluminum Sheave	: K-121XA:

Spinnaker Pole Mast Eye - New-Style -	: K-303CR:
Gooseneck Bracket SS – for 1" Toggle	: K-1209:
Gooseneck Toggle SS - 1"	: K-1993:

Clam Cleat - for Cunningham & Reef Line - CL203 (2 required)	: K-9115X:
3 1/4" Cleat - for Main & Jib Halyard (2 required)	: K-1617:
Cheek block - Original - (port)	: K-140X:
Vang Bail (SS) for Mast	: K-291A:
Mast Step Hinge Pin Assembly (5/16" diameter)	: K-84439-PA:
Mast Step - SS Hinge Plate (not included in Kit)	: K-84439:

Description	Part #
5/8" OD Round Spreaders x 19 1/4"- (Pair) - Clear Anodized	: K-FS535A-2:
Triangular Spreader Bracket, SS w/ fasteners (for 5/8" OD)	: K-366:

SP-1 Airfoil Port Spreader Assembly - Clear Anodized	: K-FS535AP:
SP-1 Starboard Spreader Assembly - Clear Anodized	: K-FS535AS:
SP-1 Port Spreader Tube only - Clear Anodized 19.5" @30°	: K-FS535TP:
SP-1 Starboard Spreader Tube only - Clear Anodized	: K-FS535TS:

SP-1 Port Spreader Assembly - Painted White	: K-FS535APW:
SP-1 Starboard Spreader Assembly - Painted White	: K-FS535ASW:

SP-1 Spreader Tip - w/ screw & locknut	: K-9409A:
SP-1 Wrap-around Spreader Bracket (for 2331 Mast, 30° aft)	: K-10756:

Description	Part #
Harpoon 5.2 Boom Assembly - 2331 Section, Clear Anodized	: K-FB535A:
- Complete w/ Toggle
Harpoon 5.2 Boom Kit - 2331 Section x 10' 3", Clear Anodized	: K-FBK535A:
w/ all Hardware and fasteners - Clear Anodized
Harpoon 5.2 - 2331 Boom Tube only x 10' 3" - Clear Anodized	: K-FBT535A:

Gooseneck Assembly w/ Tack Pin & SS Yoke	: K-43106:
Gooseneck Replacement Casting only w/ Tack Pin	: K-10448-1A:
Gooseneck Toggle	: K-1993:
Mainsheet/Vang Bail (SS) for Boom (3 required)	: K-291A:
Mainsheet Block - Aluminum Sheave	: K-121XA:
Clam Cleat - CL203 (2 required)	: K-9115X:
SS Eyestrap/Fairlead (8 required)	: K-226:
Plastic Bullseye/Fairlead - Old-Style - (8 required)	: K-226HA:
Cheek Block - Original - (2 required)	: K-140X:
Outhaul Casting	: K-10448:

Harpoon 5.2 - Other Components
Description	Part #
Elvstrom SS Bailer, 'New Large', as original - mounts from outside Hull	: Elv 11-NL:
Rubber Gasket only for Elvstrom 'New Large' SS Bailer, as original	: Elv 11-NLG:

Transom Gudgeon for 3/8" Pin - as original, but stronger	: RR 81-44H5.2:
Transom Gudgeon for 1/2" Pin - as original on later boats	: Sch 81-41:

Your cart

Spars, Rigging, and Hardware for Sailboats