SS Lifeline Stanchions, 1" OD

SS Lifeline Stanchions - 1" OD

By far the most common on boats built in North America, 1" SS Lifeline Stanchions are made from 1" OD (25.4mm) polished Stainless Steel tube with a heavy .065" wall. They have been produced with a variety of Top styles, and are occasionally, but not commonly, Tapered.
Note that a small number of North American boats were produced with 7/8" (.875") OD Stanchions, these are available in Ring Top and Flat Top versions on special order.

On boats built in Europe, most Stanchions are made from 25mm (.984") OD Stainless Steel tube, and are (almost) always Tapered. See Metric (25mm) Stanchions.
If you are replacing Tapered Stanchions and are in doubt, please measure them carefully, as 1" Stanchions Will Not fit Stanchion Bases designed for 25mm Stanchions. Metric (25mm) Stanchions will, however, fit 1" Stanchion Bases, possibly needing a wrap with Rigging or Electrical tape to fit tightly.
If you are replacing all Stanchions you can switch to a different type as long as they are the same approximate length, and the same diameter.

--------------------------
Stanchions with Integral Bases:
Stanchions are usually (and properly) separate and removable from Stanchion Bases. It is common for Stanchions, but not removable bases, to bend (when meeting pilings or other boats); we believe it is not reasonable to require a boat owner to go through the extra time, difficulty and expense of unbolting the Stanchion Bases from the deck when only a Stanchion needs to be replaced. Be advised that on many boats the Stanchion Bases were installed on the Deck before it was attached to the Hull; Stanchion Base bolts are sometimes inaccessible, being fiber-glassed over. This was an inefficient cost-cutting measure, used by only a few boat-builders. It saved (at the time) $2.-$3. dollars per unit, but ultimately cost them money (imagine the cost of Deck work involved when an entire row of Stanchions is wiped out during Transport!).

All Stanchions listed here are Stanchions only and do not include Stanchion Bases. If you have one piece Stanchions with integral Stanchion Bases (non-separable), we will try to set you up with removable units. Many of the Stanchion Bases we offer are made with the same footprint as integral units, See SS Stanchion Bases.

See also, Metric (25mm) SS Tapered Stanchions, Aluminum Stanchions, Stanchion Bases, SS Rail Bases & Hardware, and Stanchion Accessories.

1" OD Straight SS Stanchions The SS Stanchions listed below are made from 1" OD (25.4mm) polished Stainless Steel heavy wall (.065") tube. Produced with a variety of Top styles, the most common are listed below and normally available from stock. 1" OD Stanchion tube only is also available, See 1" OD Stanchion Tube. 1" OD Tapered Stanchions are listed separately, See 1" Tapered Stanchions.
*1" Single Stanchion x 24" w/ Ring Top: SA 36-R24-1:* *1" Double Stanchion x 24" w/ Ring Top: SA 36-R24-2P:* 1" OD SS Stanchion with Ring Top (R) is 24" to Top hole center. Cast SS Ring Top is welded in place. Double version has intermediate hole at 13" from the bottom, and is standard with plastic bushings (5/16" ID) in intermediate hole. Ring Top Stanchions are also available on a Custom basis at other lengths and with different intermediate hole configurations, please contact us with complete specifications.
	*"R"-Type Ring Top only for 1" Tube: ST 36-RSS1:* SS Stanchion Ring Top (R) only for 1" OD SS Stanchion tube. Cast, polished SS Ring Top has 1/2" ID Eye and projects 3/4" into tube. As used on SA 36-R24 Stanchions, above.
*1" Single Stanchion x 24" w/ Conical Top: SA 36-C24-1:* *1" Double Stanchion x 24" w/ Conical Top: SA 36-C24-2P:* 1" OD SS Stanchion with Conical Top (C) is 24" to Top hole center, cast SS Conical Top is welded in place. Double version has intermediate hole at 12" from the bottom, and is standard with plastic bushings (5/16" ID) in intermediate hole. Conical Top Stanchions are also available on a Custom basis at other lengths and with different intermediate hole configurations, please contact us with complete specifications.
*1" Single Stanchion x 24" w/ Dome Top: SA 36-D24-1:* *1" Double Stanchion x 24" w/ Dome Top: SA 36-D24-2P:* 1" OD SS Stanchion with Dome Top (D) is 24" to Top hole center, cast SS Dome Top is welded in place. Double version has intermediate hole at 12" from the bottom, and is standard with plastic bushings (5/16" ID) in intermediate hole. Dome Top Stanchions are also available on a Custom basis at other lengths and with different intermediate hole configurations, please contact us with complete specifications.
*1" Single Stanchion x 24" w/ Flat SS Top: SA 36-F24-1:* *1" Double Stanchion x 24" w/ Flat SS Top: SA 36-F24-2P:* *1" Double Stanchion x 24" w/ Flat SS Top: SA 36-F24-2S:* 1" OD SS Stanchion with highly polished, welded Flat Top (F) is 24" to Top hole center. Double version has intermediate hole at 12" from the bottom, and is available with P plastic insert bushings (5/16" ID), or S solid insert (3/8" ID) intermediate hole. Flat Top Stanchions are also available on a Custom basis at other lengths and with different intermediate hole configurations, please contact us with complete specifications.
*1" Single Stanchion x 24" w/ "FP" Flat Top: SA 36-FP24-1:* *1" Double Stanchion x 24" w/ "FP" Flat Top: SA 36-FP24-2:* 1" OD SS Stanchion with FP Flat Top is 24" to Top hole center. FP Flat Top is produced by inserting Black Delrin plug before turning stanchion to length, upper hole (>3/8" (.410" diameter)) is drilled through solid insert. Double version has solid insert intermediate hole (1/4" ID) at 12" from the bottom. Black plug end may age gray. As used on a variety of Cape Dory Yachts, and others. These items are no longer available, use *SA 36-FP24-1B* and SA 36-FP24-2B, below, or *SA 36-F24-1* or *SA 36-F24-2*, above.
*1" Single Stanchion x 24" w/ "FP" Flat Top & Brace Hole: SA 36-FP24-1B:* *1" Double Stanchion x 24" w/ "FP" Flat Top & Brace Hole: SA 36-FP24-2B:*
1" OD SS Stanchions with FP Flat Top are as *SA 36-FP24-1* and SA 36-FP24-2, above, but with a 1/4" thru-hole at 7 1/4" from the top for use with Gate Brace. As used on a variety of Cape Dory Yachts.
*1" Single Stanchion x 24" w/ Schaefer Top: SA 36-S24-1:* *1" Double Stanchion x 24" w/ Schaefer Top: SA 36-S24-2:* 1" OD SS Schaefer Stanchion has Flatish black plastic Top plug inserted before holes are pressed. Top hole center is at 24 3/8", Double version has solid insert intermediate hole (3/8" ID) at 11 3/4" from bottom.
*1" Single Stanchion x 26" w/ Schaefer Top: SA 36-S26-1:* *1" Double Stanchion x 26" w/ Schaefer Top: SA 36-S26-2:* 1" OD SS Schaefer Stanchion has Flatish black plastic Top plug inserted before holes are pressed. Top hole center is at 26 3/8", Double version has solid insert intermediate hole (3/8" ID) at 12" from the top hole.

1" OD Tapered SS Stanchions The SS Stanchions listed below are made from 1" OD (25.4mm) polished Stainless Steel tube with a heavy .065" wall. Tapered to approximately 5/8" and welded to a variety of Top styles, the most common are listed below. Other configurations of 1" Tapered SS Stanchions are available, please contact us with complete specifications. The most common SS Tapered Stanchions are actually Metric 25mm OD, See 25mm (Metric) Tapered Stanchions.
*1" Tapered Single Stanchion x 24" w/ Tube Top: SA 36-TT24-1:* *1" Tapered Double Stanchion x 24" w/ Tube Top: SA 36-TT24-2SF:* *1" Tapered Double Stanchion x 24" w/ Tube Top: SA 36-TT24-2SR:*
1" OD Tapered SS Stanchion with Tube Top is 24" to Top hole center. Stanchion is tapered to approximately 5/8" and welded to SS Tube. Double version is standard with Flared SS Ferrule (3/8" ID) for intermediate hole at 12" from the bottom and is also available with a Rolled SS Ferrule. Tapered Tube Top Stanchions are also available on a Custom basis at other lengths and with different intermediate hole configurations, please contact us with complete specifications.

Your cart

Spars, Rigging, and Hardware for Sailboats